Zobrazit minimální záznam

Design of Semiautomatic Assembly of Connector with O-ring



dc.contributor.advisorMrázek Jiří
dc.contributor.authorNoháč Marek
dc.date.accessioned2017-06-07T16:19:47Z
dc.date.available2017-06-07T16:19:47Z
dc.date.issued2017-06-06
dc.identifierKOS-695600113805
dc.identifier.urihttp://hdl.handle.net/10467/70399
dc.description.abstractLisování zaujímá ve strojírenství podstatnou část spojení součástí především z důvodu jeho nízké ceny a možností vysokých přenosů sil a výkonů. Teoretická část této práce je zaměřena na souhrn informací ohledně lisování, jeho kvalitě a možnosti řízení při lisování, a to především se zaměřením na součásti typu náboj-hřídel, ale i instalace O-kroužků do drážek a způsoby jejich výpočtu. Úkolem praktické části práce je na základě získaných informací z norem o lisování a ze zadání požadavků zákazníka vytvořit návrhový model zařízení, na kterém by bylo možné provádět lisování O-kroužků na konektor a následné zalisování konektoru do tělesa.cze
dc.description.abstractPressing occupies a significant part of the joining of parts in mechanical engineering, mainly due to its low price and high power transmission capabilities. The theoretical part of the thesis focused on the summary of information on pressing, its quality and the possibilities of stamping, especially with focus on hub-shaft components, as well as installation of O-rings in the grooves and ways of their calculation. The task of the practical part of the thesis is based on the obtained information from the standards of pressing and the requirements of the customer to create a design model of the device on which it is possible to perform the O-ring pressing on the connector and the subsequent pressing of the connector into the body.eng
dc.language.isoCZE
dc.publisherČeské vysoké učení technické v Praze. Vypočetní a informační centrum.cze
dc.publisherCzech Technical University in Prague. Computing and Information Centre.eng
dc.rightsA university thesis is a work protected by the Copyright Act. Extracts, copies and transcripts of the thesis are allowed for personal use only and at one?s own expense. The use of thesis should be in compliance with the Copyright Act http://www.mkcr.cz/assets/autorske-pravo/01-3982006.pdf and the citation ethics http://knihovny.cvut.cz/vychova/vskp.htmleng
dc.rightsVysokoškolská závěrečná práce je dílo chráněné autorským zákonem. Je možné pořizovat z něj na své náklady a pro svoji osobní potřebu výpisy, opisy a rozmnoženiny. Jeho využití musí být v souladu s autorským zákonem http://www.mkcr.cz/assets/autorske-pravo/01-3982006.pdf a citační etikou http://knihovny.cvut.cz/vychova/vskp.htmlcze
dc.subjectPoloautomatická montážní stanice, lisování, O-kroužek, bezpečnost, automatizace, konektor, návrh konstrukce, metodika měření času MTM, MANN+HUMMELcze
dc.subjectSemi-automatic assembly station, pressing, O-ring, safety, automatization, connector, design of the construction, method time measurement MTM, MANN+HUMMELeng
dc.titleNávrh poloautomatické montážní stanice konektoru s O-kroužkemcze
dc.titleDesign of Semiautomatic Assembly of Connector with O-ringeng
dc.typediplomová prácecze
dc.typemaster thesiseng
dc.date.accepted
dc.contributor.refereeVosecký Miloš
theses.degree.disciplineDopravní, letadlová a transportní technikacze
theses.degree.grantorústav konstruování a částí strojůcze
theses.degree.programmeStrojní inženýrstvícze


Soubory tohoto záznamu







Tento záznam se objevuje v následujících kolekcích

Zobrazit minimální záznam