Hodnocení struktury a mechanických vlastností 3D tištěné slitiny AlSi10Mg v závislosti na parametrech tepelného zpracování
Evaluation of structure and mechanical properties of 3D printed alloy AlSi10Mg depending on heat treatment parameters
dc.contributor.advisor | Sobotová Jana | |
dc.contributor.author | Eliška Galčíková | |
dc.date.accessioned | 2022-08-28T22:51:51Z | |
dc.date.available | 2022-08-28T22:51:51Z | |
dc.date.issued | 2022-08-28 | |
dc.identifier | KOS-1201007104105 | |
dc.identifier.uri | http://hdl.handle.net/10467/103634 | |
dc.description.abstract | Předložená diplomová práce hodnotí vliv tepelného zpracování na strukturu a mechanické vlastnosti 3D tištěné slitiny AlSi10Mg. U vzorků vyrobených metodou tavení v práškovém loži byly porovnávány 4 režimy žíhání, při teplotách 240 °C a 300 °C s variantním časovým průběhem a způsobem ochlazení, se stavem as-built. Mechanické vlastnosti u všech stavů byly zkoumány zkouškou tahem a měřením tvrdosti, zkouška únavy byla hodnocena pouze pro stav as-built. Metalografická analýza byla provedena pomocí světelné a řádkovací elektronové mikroskopie, která byla doplněna o analýzu chemického složení metodou EDS. | cze |
dc.description.abstract | The presented thesis evaluates the effect of heat treatment on the structure and mechanical properties of the 3D printed AlSi10Mg alloy. Samples produced by laser powder bed fusion after 4 annealing modes at temperatures of 240 °C and 300 °C with a variant time and variant cooling method were compared with the as-built state. Mechanical properties in all states were investigated by tensile test and hardness measurement, fatigue test was evaluated only for the as-built state. Light microscopy and scanning electron microscopy was used for the metallographic analysis. Scanning electron microscopy was supplemented by an analysis of the chemical composition using the EDS method. | eng |
dc.publisher | České vysoké učení technické v Praze. Vypočetní a informační centrum. | cze |
dc.publisher | Czech Technical University in Prague. Computing and Information Centre. | eng |
dc.rights | A university thesis is a work protected by the Copyright Act. Extracts, copies and transcripts of the thesis are allowed for personal use only and at one?s own expense. The use of thesis should be in compliance with the Copyright Act http://www.mkcr.cz/assets/autorske-pravo/01-3982006.pdf and the citation ethics http://knihovny.cvut.cz/vychova/vskp.html | eng |
dc.rights | Vysokoškolská závěrečná práce je dílo chráněné autorským zákonem. Je možné pořizovat z něj na své náklady a pro svoji osobní potřebu výpisy, opisy a rozmnoženiny. Jeho využití musí být v souladu s autorským zákonem http://www.mkcr.cz/assets/autorske-pravo/01-3982006.pdf a citační etikou http://knihovny.cvut.cz/vychova/vskp.html | cze |
dc.subject | AlSi10Mg | cze |
dc.subject | 3D tisk | cze |
dc.subject | SLM/DMLM | cze |
dc.subject | žíhání při středních teplotách | cze |
dc.subject | mikrostruktura | cze |
dc.subject | mechanické vlastnosti | cze |
dc.subject | AlSi10Mg | eng |
dc.subject | 3D printing | eng |
dc.subject | SLM/DMLM | eng |
dc.subject | intermediate annealing treatments/stress relief treatment | eng |
dc.subject | microstructure | eng |
dc.subject | mechanical properties | eng |
dc.title | Hodnocení struktury a mechanických vlastností 3D tištěné slitiny AlSi10Mg v závislosti na parametrech tepelného zpracování | cze |
dc.title | Evaluation of structure and mechanical properties of 3D printed alloy AlSi10Mg depending on heat treatment parameters | eng |
dc.type | diplomová práce | cze |
dc.type | master thesis | eng |
dc.contributor.referee | Hudec Jan | |
theses.degree.discipline | Bez specializace | cze |
theses.degree.grantor | ústav materiálového inženýrství | cze |
theses.degree.programme | Výrobní inženýrství | cze |
Soubory tohoto záznamu
Tento záznam se objevuje v následujících kolekcích
-
Diplomové práce - 12132 [104]