Vstřikování termoplastů vyztužených krátkými skleněnými vlákny – Analýza orientace a homogenizace vláken ve výstřiku
Injection moulding of short glass-fibre reinforced thermoplastics - Analysis of fibre orientation and homogenization in the moulding
Typ dokumentu
disertační prácedoctoral thesis
Autor
Stefan Krebs
Vedoucí práce
Kolařík Ladislav
Oponent práce
Kříž Antonín
Studijní obor
Strojírenská technologieStudijní program
Strojní inženýrstvíInstituce přidělující hodnost
ústav strojírenské technologiePráva
A university thesis is a work protected by the Copyright Act. Extracts, copies and transcripts of the thesis are allowed for personal use only and at one?s own expense. The use of thesis should be in compliance with the Copyright Act http://www.mkcr.cz/assets/autorske-pravo/01-3982006.pdf and the citation ethics http://knihovny.cvut.cz/vychova/vskp.htmlVysokoškolská závěrečná práce je dílo chráněné autorským zákonem. Je možné pořizovat z něj na své náklady a pro svoji osobní potřebu výpisy, opisy a rozmnoženiny. Jeho využití musí být v souladu s autorským zákonem http://www.mkcr.cz/assets/autorske-pravo/01-3982006.pdf a citační etikou http://knihovny.cvut.cz/vychova/vskp.html
Metadata
Zobrazit celý záznamAbstrakt
Disertační práce se zabývá tématem vstřikování termoplastů vyztužených krátkými skleněnými vlákny. Zaměřuje se na analýzu a vyhodnocení orientace a homogenizace vláken ve výstřiku. Ačkoli výraz „krátká skleněná vlákna“ budí dojem, že orientace a homogenita vláken ve složce nehrají zvláštní roli, předložená disertační práce ukazuje, že tyto faktory jsou pro mechanické vlastnosti výrobků vyrobených vstřikováním velmi důležité. Disertační práce se zabývá příčinami praskání zkušebních těles při axiálním zatížení na příkladu polyamidu PA66+PA6, který je vyztužen krátkými skleněnými vlákny (s 30 hmot. %). Ke praskáním dochází opakovaně na atypickém místě. Toto pozorování je dříve nezdokumentované a neprozkoumané. Je to dobrý příklad důležitosti orientace vláken a homogenity ve výlisku. Pro tento účel byly v práci definovány koeficienty pevnosti a použity vhodné zkušební metody: zkouška tahem, plastografie, analýza spalování plastu (tzv. "ash test") a konfokální laserová mikroskopie. Disertační práce dále se zabývá stávajícími analytickými modely pro tok taveniny v dutině a pokouší se je prokázat analýzou orientace vláken. Analytické modely, zkušební metody a počítačová simulace shromážděné v práci mohou být příspěvkem pro průmyslovou praxi a přispět k optimalizaci mechanických vlastností a řešení chyb v návrhu vstřikovaných součástí. This dissertation deals with the injection moulding of thermoplastics reinforced with short glass fibres. It focuses on the analysis and investigation of the orientation and homogenization of fibres in the moulding. Although the term "short glass fibres" gives the impression that the orientation and homogeneity of the fibres in the component do not play a special role, this dissertation shows that these factors are very important for the mechanical properties. The dissertation deals with the causes of cracking of test specimens under axial load on the example of polyamide PA66 + PA6, which is reinforced with short glass fibres (with 30% by weight). Cracks occur repeatedly in an atypical location. This observation is previously undocumented and unexplored. This is a good example of the importance of fibre orientation and homogeneity in the moulding. For this purpose, coefficients for tensile strength were defined and suitable test methods were used: tensile test, plastography, analysis of plastic combustion (so-called "ash test") and confocal laser microscopy. This dissertation deals with existing analytical models for melt flow in the cavity and tries to prove them by analytical methods. Analytical models, test methods and computer simulation collected in the dissertation can be a contribution to further investigation of complex phenomena or in practice contribute to the solution of errors in components.
Kolekce
- Disertační práce - 12000 [279]