Vliv parametrů tepelného zpracování na užitné vlastnosti slitiny AlSi10Mg vyrobené 3D tiskem
Influence of heat treatment parameters on utility properties of AlSi10Mg alloy produced by 3D printing
dc.contributor.advisor | Sobotová Jana | |
dc.contributor.author | Ludmila Růžičková | |
dc.date.accessioned | 2020-08-23T22:52:03Z | |
dc.date.available | 2020-08-23T22:52:03Z | |
dc.date.issued | 2020-08-23 | |
dc.identifier | KOS-985499148505 | |
dc.identifier.uri | http://hdl.handle.net/10467/89802 | |
dc.description.abstract | Předložená diplomová práce hodnotí vliv tepelného zpracování žíháním ke snížení pnutí na 3D tištěnou slitinu AlSi10Mg vytištěnou metodou SLM (Selective laser melting). Byla provedena CT analýza, metalografická analýza, zkouška tahem, fraktografická analýza a měřena tvrdost. Byly zvoleny tři režimy žíhání: 240 °C/6 hod; 240 °C/2 hod; 300 °C/2 hod. Pro stanovení vlivu režimu žíhání na mechanické vlastnosti 3D tištěné slitiny AlSi10Mg byly výsledky získané měřením porovnány se stavem as-built a také mezi sebou. | cze |
dc.description.abstract | Presented diploma thesis evaluates the effect of heat treatment of stress relieving on a SLM (Selective Laser Melting) 3D printed AlSi10Mg alloy. CT analysis, metallographic analysis, tensile test, fractographic analysis and hardness are measured. Three stress relieving modes were selected: 240 °C/6 hours; 240 °C/2 hours; 300 °C/2 hours. To determine the effect of the annealing mode on the mechanical properties of the 3D printed AlSi10Mg alloy, the results obtained by measurement were compared with the as-built state and with each other. | eng |
dc.publisher | České vysoké učení technické v Praze. Vypočetní a informační centrum. | cze |
dc.publisher | Czech Technical University in Prague. Computing and Information Centre. | eng |
dc.rights | A university thesis is a work protected by the Copyright Act. Extracts, copies and transcripts of the thesis are allowed for personal use only and at one?s own expense. The use of thesis should be in compliance with the Copyright Act http://www.mkcr.cz/assets/autorske-pravo/01-3982006.pdf and the citation ethics http://knihovny.cvut.cz/vychova/vskp.html | eng |
dc.rights | Vysokoškolská závěrečná práce je dílo chráněné autorským zákonem. Je možné pořizovat z něj na své náklady a pro svoji osobní potřebu výpisy, opisy a rozmnoženiny. Jeho využití musí být v souladu s autorským zákonem http://www.mkcr.cz/assets/autorske-pravo/01-3982006.pdf a citační etikou http://knihovny.cvut.cz/vychova/vskp.html | cze |
dc.subject | 3D tisk | cze |
dc.subject | AlSi10Mg | cze |
dc.subject | SLM | cze |
dc.subject | žíhání ke snížení pnutí | cze |
dc.subject | mechanické vlastnosti | cze |
dc.subject | struktura | cze |
dc.subject | 3D printing | eng |
dc.subject | AlSi10Mg | eng |
dc.subject | SLM | eng |
dc.subject | stress relieving | eng |
dc.subject | mechanical properties | eng |
dc.subject | structure | eng |
dc.title | Vliv parametrů tepelného zpracování na užitné vlastnosti slitiny AlSi10Mg vyrobené 3D tiskem | cze |
dc.title | Influence of heat treatment parameters on utility properties of AlSi10Mg alloy produced by 3D printing | eng |
dc.type | diplomová práce | cze |
dc.type | master thesis | eng |
dc.contributor.referee | Hudec Jan | |
theses.degree.discipline | Výrobní a materiálové inženýrství | cze |
theses.degree.grantor | ústav materiálového inženýrství | cze |
theses.degree.programme | Strojní inženýrství | cze |
Soubory tohoto záznamu
Tento záznam se objevuje v následujících kolekcích
-
Diplomové práce - 12132 [109]