Vliv parametrů tepelného zpracování na odolnost proti opotřebení 3D tiskem připravené slitiny AlSi10Mg
Influence of heat treatment parameters on wear resistance of AlSi10Mg alloy prepared by 3D printing
dc.contributor.advisor | Sobotová Jana | |
dc.contributor.author | Tomáš Růžička | |
dc.date.accessioned | 2020-08-22T22:51:55Z | |
dc.date.available | 2020-08-22T22:51:55Z | |
dc.date.issued | 2020-08-22 | |
dc.identifier | KOS-981032550605 | |
dc.identifier.uri | http://hdl.handle.net/10467/89745 | |
dc.description.abstract | Bakalářská práce se zabývá hodnocením vlivu parametrů tepelného zpracování na odolnost proti opotřebení 3D tiskem připravené slitiny AlSi10Mg. V teoretické části jsou uvedeny základní informace o technologiích 3D tisku kovu. Jsou zde také popsány základní vlastnosti hliníku a jeho slitin. Experimentální část se zabývá testováním vzorků z AlSi10Mg. Materiál je sledován ve stavu bez tepelného zpracování a po třech různých režimech žíhání. K hodnocení je použita zkouška Pin-on Disk, měření tvrdosti a metalografická analýza. | cze |
dc.description.abstract | The bachelor thesis deals with the evaluation of the influence of heat treatment parameters on wear resistance of AlSi10Mg alloy prepared by 3D printing. The theoretical part provides basic information about 3D metal printing technologies. The basic properties of aluminum and its all-oys are also described here. The experimental part deals with testing samples from AlSi10Mg. The material is monitored in a state without heat treatment and after three different annealing modes. Pin-on Disk test, hardness measurement and metallographic analysis are used for evaluati-on. | eng |
dc.publisher | České vysoké učení technické v Praze. Vypočetní a informační centrum. | cze |
dc.publisher | Czech Technical University in Prague. Computing and Information Centre. | eng |
dc.rights | A university thesis is a work protected by the Copyright Act. Extracts, copies and transcripts of the thesis are allowed for personal use only and at one?s own expense. The use of thesis should be in compliance with the Copyright Act http://www.mkcr.cz/assets/autorske-pravo/01-3982006.pdf and the citation ethics http://knihovny.cvut.cz/vychova/vskp.html | eng |
dc.rights | Vysokoškolská závěrečná práce je dílo chráněné autorským zákonem. Je možné pořizovat z něj na své náklady a pro svoji osobní potřebu výpisy, opisy a rozmnoženiny. Jeho využití musí být v souladu s autorským zákonem http://www.mkcr.cz/assets/autorske-pravo/01-3982006.pdf a citační etikou http://knihovny.cvut.cz/vychova/vskp.html | cze |
dc.subject | Aditivní výroba | cze |
dc.subject | 3D tisk | cze |
dc.subject | hliník | cze |
dc.subject | AlSi10Mg | cze |
dc.subject | struktura | cze |
dc.subject | Pin-on-Disk | cze |
dc.subject | odolnost proti opotřebení | cze |
dc.subject | Additive Manufacturing | eng |
dc.subject | 3D printing | eng |
dc.subject | aluminium | eng |
dc.subject | AlSi10Mg | eng |
dc.subject | structure | eng |
dc.subject | Pin-on-Disk | eng |
dc.subject | wear resistance | eng |
dc.title | Vliv parametrů tepelného zpracování na odolnost proti opotřebení 3D tiskem připravené slitiny AlSi10Mg | cze |
dc.title | Influence of heat treatment parameters on wear resistance of AlSi10Mg alloy prepared by 3D printing | eng |
dc.type | bakalářská práce | cze |
dc.type | bachelor thesis | eng |
dc.contributor.referee | Hudec Jan | |
theses.degree.discipline | Technologie, materiály a ekonomika strojírenství | cze |
theses.degree.grantor | ústav materiálového inženýrství | cze |
theses.degree.programme | Výroba a ekonomika ve strojírenství | cze |
Soubory tohoto záznamu
Tento záznam se objevuje v následujících kolekcích
-
Bakalářské práce - 12132 [154]