ČVUT DSpace
  • Search DSpace
  • Čeština
  • Login
  • Čeština
  • Čeština
View Item 
  •   ČVUT DSpace
  • Czech Technical University in Prague
  • Faculty of Electrical Engineering
  • Department of Electrotechnology
  • Bachelor Theses - 13113
  • View Item
  • Czech Technical University in Prague
  • Faculty of Electrical Engineering
  • Department of Electrotechnology
  • Bachelor Theses - 13113
  • View Item
JavaScript is disabled for your browser. Some features of this site may not work without it.

Izolační vlastnosti výrobků vytištěných 3D tiskovou technologií FDM

Insulation properties of FFF 3D printed products

Type of document
bakalářská práce
bachelor thesis
Author
Tomáš Cápal
Supervisor
Tichý Tomáš
Opponent
Kněnický Martin
Field of study
Aplikovaná elektrotechnika
Study program
Elektrotechnika, energetika a management
Institutions assigning rank
katedra elektrotechnologie



Rights
A university thesis is a work protected by the Copyright Act. Extracts, copies and transcripts of the thesis are allowed for personal use only and at one?s own expense. The use of thesis should be in compliance with the Copyright Act http://www.mkcr.cz/assets/autorske-pravo/01-3982006.pdf and the citation ethics http://knihovny.cvut.cz/vychova/vskp.html
Vysokoškolská závěrečná práce je dílo chráněné autorským zákonem. Je možné pořizovat z něj na své náklady a pro svoji osobní potřebu výpisy, opisy a rozmnoženiny. Jeho využití musí být v souladu s autorským zákonem http://www.mkcr.cz/assets/autorske-pravo/01-3982006.pdf a citační etikou http://knihovny.cvut.cz/vychova/vskp.html
Metadata
Show full item record
Abstract
Tato práce se zabývá výzkumem izolačních vlastností výtisků vytištěnými na 3D tiskárně za použití FDM metody. V úvodní části je vysvětlen princip FDM metody a popis použitých komerčně dostupných materiálů. U těchto vytisknutých materiálů na 3D tiskárně se zkoumala jejich elektrická pevnost využitím různých druhů metod k tomu určené. Měření bylo provedeno na rázové zkoušce a krátkodobé zkoušce s konstantním nárůstem napětí. V závěru měření se dále pozoroval vliv nerovnosti povrchu výtisků na dielektrickou pevnost. Hlavním cílem je vybrat nejvhodnější metodu měření elektrické pevnosti pro výtisky tištěné na 3D tiskárně Prusa i3 MK3 a určit materiál s nejvyššími izolačními vlastnostmi.
 
This work deals with research of insulation properties of prints printed on 3D printer using FDM method. In the introductory part there is the principle of FDM method and description of used commercially available materials explained. These printed materials on a 3D printer were examined for their electrical strength using various types of methods designated for this purpose. The measurement was performed on the impact test and the short-term test with rapid voltage rise. At the end of the measurement, the effect of surface irregularities on dielectric strength was also observed. The main goal is to select the most suitable method of measuring electrical strength for prints printed on the 3D printer Prusa i3 MK3 and to determine the material with the highest insulation properties.
 
URI
http://hdl.handle.net/10467/87610
View/Open
PLNY_TEXT (2.208Mb)
PRILOHA (1.283Mb)
POSUDEK (468.0Kb)
POSUDEK (233.3Kb)
Collections
  • Bakalářské práce - 13113 [160]

České vysoké učení technické v Praze copyright © 2016 

DSpace software copyright © 2002-2016  Duraspace

Contact Us | Send Feedback
Theme by 
@mire NV
 

 

Useful links

CTU in PragueCentral library of CTUAbout CTU Digital LibraryResourcesStudy and library skillsResearch support

Browse

All of DSpaceCommunities & CollectionsBy Issue DateAuthorsTitlesSubjectsThis CollectionBy Issue DateAuthorsTitlesSubjects

My Account

Login

České vysoké učení technické v Praze copyright © 2016 

DSpace software copyright © 2002-2016  Duraspace

Contact Us | Send Feedback
Theme by 
@mire NV