Vliv tepelného zpracování na vlastnosti pružinové oceli 54SiCr6
Effect of heat treatment on properties of 54SiCr6 spring steel
Typ dokumentu
diplomová prácemaster thesis
Autor
Otakar Kuchař
Vedoucí práce
Sobotová Jana
Oponent práce
Šedivý Otomar
Studijní obor
Výrobní a materiálové inženýrstvíStudijní program
Strojní inženýrstvíInstituce přidělující hodnost
ústav materiálového inženýrstvíPráva
A university thesis is a work protected by the Copyright Act. Extracts, copies and transcripts of the thesis are allowed for personal use only and at one?s own expense. The use of thesis should be in compliance with the Copyright Act http://www.mkcr.cz/assets/autorske-pravo/01-3982006.pdf and the citation ethics http://knihovny.cvut.cz/vychova/vskp.htmlVysokoškolská závěrečná práce je dílo chráněné autorským zákonem. Je možné pořizovat z něj na své náklady a pro svoji osobní potřebu výpisy, opisy a rozmnoženiny. Jeho využití musí být v souladu s autorským zákonem http://www.mkcr.cz/assets/autorske-pravo/01-3982006.pdf a citační etikou http://knihovny.cvut.cz/vychova/vskp.html
Metadata
Zobrazit celý záznamAbstrakt
Práce se zabývá hodnocením vlastností a struktury pružinové oceli 54SiCr6 v rámci různých podmínek tepelného zpracování. Vzorky A byly žíhány ke snížení pnutí při teplotě 300, 340, 380 a 420 °C po dobu 20 a 40 minut v laboratorní pícce. U těchto vzorků byla provedena zkouška tahem, modifikované zkouška rázem v ohybu, u části z nich zkouška tvrdosti dle Vickerse a metalografická analýza. Vzorky B – pružiny byly žíhány při teplotě 300, 340, 390 a 410 °C po dobu 20 minut v plynové průběžné peci. Zároveň bylo u pružin uskutečněno měření úhlu navinutí před a po tepelném zpracování a také po vibrační lázni. U vybraných pružin byly provedeny zkoušky životnosti, u dalších vybraných poté rentgenová difrakční analýza. Teplota žíhání má vliv na vlastnosti sledovaných stavů. Naopak rozdíl doby žíhání (20 a 40 minut) se ukázal jako nevýrazný. Teplota 420 °C se z hlediska dosažených výsledků jeví jako nevhodná. The work is focused on evaluation of properties and structure of spring steel 54SiCr6 for different heat treatment conditions. Specimens A were stress relief annealed for 20 and 40 minutes at 300, 340, 380 and 420 °C in a laboratory furnace. In addition, the specimens were subjected to the tensile test, modified impact test, some of them to the Vickers hardness test and metallographic analysis. Specimens B – springs were annealed for 20 minutes at 300, 340, 390 and 410 °C in a gas continuous furnace. At the same time, the springs were measured for the winding angle before and after the heat treatment and also after the vibration bath, which followed the heat treatment process. Durability tests and X-ray diffraction analysis were performed on selected springs. The influence of the annealing temperature on the properties of the monitored states was proved, while the choice of the annealing time (20 and 40 minutes) has no significant effect. The temperature of 420 °C seems unsuitable in view of the results obtained.
Kolekce
- Diplomové práce - 12132 [109]