Hodnocení nástrojů při obrábění slitiny niklu frézováním
Evaluluation of tools for machining of nickel alloy during milling
dc.contributor.advisor | Rázek Vítězslav | |
dc.contributor.author | Vojtěch Forman | |
dc.date.accessioned | 2019-06-27T22:53:39Z | |
dc.date.available | 2019-06-27T22:53:39Z | |
dc.date.issued | 2019-06-27 | |
dc.identifier | KOS-883223099105 | |
dc.identifier.uri | http://hdl.handle.net/10467/84371 | |
dc.description.abstract | Cílem diplomové práce je zhodnocení kvality povrchu obráběné niklové slitiny Inconel 713 LC na základě integrity povrchu a vliv na nástroje při jejím frézování. Součástí tohoto zhodnocení je analýza sil, které vznikají při čelním frézování, měření drsnosti povrchu a tvrdosti ve zpevněné povrchové vrstvě po obrábění a analýza zbytkových napětí. Zároveň bude provedeno měření opotřebení nástrojů po obrábění. Teoretická část bude obsahovat úvod do problematiky niklových slitin a jejich obrábění. Dále bude v teoretické části přiblížena problematika integrity povrchu a metody jejího měření, včetně mechanismů opotřebení nástroje při obrábění. Experimentální část pak bude zaměřena na samotné měření a vyhodnocování sil při čelním frézování, opotřebení nástrojů a integrity povrchu s ohledem na různé řezné podmínky a různou geometrii nástroje. | cze |
dc.description.abstract | The aim of this thesis is to evaluate the surface quality of machined nickel alloy Inconel 713 LC on the basis of surface integrity and influence on the tools during its milling. Part of this assessment is the analysis of the forces generated by face milling, surface roughness measurements, hardness in the reinforced surface layer after machining and residual stresses analysis. The after machining tools wear will be measured as well. The theoretical part will include an introduction to nickel alloys and their machining. Further, in the theoretical part, the issue of surface integrity and methods of its measurement, including tool wear mechanisms during machining, will be discussed. The experimental part will then be focused on the measurement and evaluation of forces in face milling, tool wear and surface integrity with respect to different cutting conditions and different tool geometry. | eng |
dc.publisher | České vysoké učení technické v Praze. Vypočetní a informační centrum. | cze |
dc.publisher | Czech Technical University in Prague. Computing and Information Centre. | eng |
dc.rights | A university thesis is a work protected by the Copyright Act. Extracts, copies and transcripts of the thesis are allowed for personal use only and at one?s own expense. The use of thesis should be in compliance with the Copyright Act http://www.mkcr.cz/assets/autorske-pravo/01-3982006.pdf and the citation ethics http://knihovny.cvut.cz/vychova/vskp.html | eng |
dc.rights | Vysokoškolská závěrečná práce je dílo chráněné autorským zákonem. Je možné pořizovat z něj na své náklady a pro svoji osobní potřebu výpisy, opisy a rozmnoženiny. Jeho využití musí být v souladu s autorským zákonem http://www.mkcr.cz/assets/autorske-pravo/01-3982006.pdf a citační etikou http://knihovny.cvut.cz/vychova/vskp.html | cze |
dc.subject | Nikl | cze |
dc.subject | Inconel | cze |
dc.subject | čelní frézování | cze |
dc.subject | integrita povrchu | cze |
dc.subject | síly při obrábění | cze |
dc.subject | drsnost | cze |
dc.subject | opotřebení nástroje | cze |
dc.subject | mikrotvrdost | cze |
dc.subject | zpevnění | cze |
dc.subject | zbytková napětí | cze |
dc.subject | Nickel | eng |
dc.subject | Inconel | eng |
dc.subject | face milling | eng |
dc.subject | surface integrity | eng |
dc.subject | cutting forces | eng |
dc.subject | roughness | eng |
dc.subject | tool wear | eng |
dc.subject | microhardness | eng |
dc.subject | hardening | eng |
dc.subject | residual stress | eng |
dc.title | Hodnocení nástrojů při obrábění slitiny niklu frézováním | cze |
dc.title | Evaluluation of tools for machining of nickel alloy during milling | eng |
dc.type | diplomová práce | cze |
dc.type | master thesis | eng |
dc.contributor.referee | Vilcsek Igor | |
theses.degree.discipline | Výrobní a materiálové inženýrství | cze |
theses.degree.grantor | ústav technologie obrábění, projektování a metrologie | cze |
theses.degree.programme | Strojní inženýrství | cze |
Soubory tohoto záznamu
Tento záznam se objevuje v následujících kolekcích
-
Diplomové práce - 12134 [225]