ČVUT DSpace
  • Search DSpace
  • Čeština
  • Login
  • Čeština
  • Čeština
View Item 
  •   ČVUT DSpace
  • Czech Technical University in Prague
  • Faculty of Mechanical Engineering
  • Department of Automotive, Combustion Engine and Railway
  • Master Theses - 12120
  • View Item
  • Czech Technical University in Prague
  • Faculty of Mechanical Engineering
  • Department of Automotive, Combustion Engine and Railway
  • Master Theses - 12120
  • View Item
JavaScript is disabled for your browser. Some features of this site may not work without it.

Studie geometrických parametrů trysky pro použití v chladicím cyklu zařízení využívající zbytkové teplo

Geometric nozzle study for an ejection cycle used for waste heat recovery system

Type of document
diplomová práce
master thesis
Author
Gopalakrishnan Deepak Kumar Jangid
Supervisor
Doleček Vít
Opponent
Toman Rastislav
Field of study
Advanced Powertrains
Study program
Master of Automotive Engineering
Institutions assigning rank
ústav automobilů, spalovacích motorů a kolejových vozidel
Defended
2019-02-07



Rights
A university thesis is a work protected by the Copyright Act. Extracts, copies and transcripts of the thesis are allowed for personal use only and at one?s own expense. The use of thesis should be in compliance with the Copyright Act http://www.mkcr.cz/assets/autorske-pravo/01-3982006.pdf and the citation ethics http://knihovny.cvut.cz/vychova/vskp.html
Vysokoškolská závěrečná práce je dílo chráněné autorským zákonem. Je možné pořizovat z něj na své náklady a pro svoji osobní potřebu výpisy, opisy a rozmnoženiny. Jeho využití musí být v souladu s autorským zákonem http://www.mkcr.cz/assets/autorske-pravo/01-3982006.pdf a citační etikou http://knihovny.cvut.cz/vychova/vskp.html
Metadata
Show full item record
Abstract
V diplomové práci je provedena studie provozního režimu ejektoru použitého v chladícím cyklu. Studie byla provedena s využitím výpočetních metod mechaniky tekutin a je zaměřena na ověření citlivosti ejektoru provozu na jeho geometrii při provozu. Hlavním úkolem bylo zlepšení provozních vlastností a výkonu ejektrou, který je ovlivněn snížením tlakových ztrát a maximalizací poměru sekundárního a primárního proudu. Provoz ejektroru s optimálizovanou geometrií byl ověřen při nenávrhových stavech. Simulace v rámci projektu byly prováděny pomocí komerčního CFD programu. První částí byla tvorba geometrie a tvorba výpočetní sítě. Dále byly stanoveny okrajové podmínky pro výpočet ejektoru a byla provedena simulace, která byla následně vyhodnocena a analyzována. Na závěr byla provedena analýza chování ejektoru v nenávrhových stavech systému.
 
In this thesis work, a detailed study is carried out on the operation of an integrated ejector in a refrigeration cycle. The study has been done using mechanical simulation program of computational fluid and aims to check the response of the different geometries of the ejector at final operating conditions. The primary attention was given to the ejector geometry which produces better performance, i.e., the geometry which minimizes the loss of pressure in the flow and maximizes the ratio between the secondary and primary mass flow rate. After the ejector geometry which produces optimum performance is found, the optimum geometry is studied in off-design operating conditions to check if there is any reduction in the performance of the optimum ejector geometry. Throughout the project work, all the necessary steps are taken to configure and solve the problem by using CFD simulation program. It is established as a starting point by setting up the geometry followed by meshing process and mesh quality study. In the preprocessing, the attention is given to the definition of the boundary conditions of the problem. The problem is initialized and the simulated by using the resolution strategy. The process is concluded with the post-processing phase and results of the analysis. The performance of optimum and non-optimum ejector geometries is studied in detail with the flow behavior inside the ejector.
 
URI
http://hdl.handle.net/10467/80823
View/Open
PLNY_TEXT (2.072Mb)
POSUDEK (439.1Kb)
POSUDEK (216.3Kb)
Collections
  • Diplomové práce - 12120 [456]

České vysoké učení technické v Praze copyright © 2016 

DSpace software copyright © 2002-2016  Duraspace

Contact Us | Send Feedback
Theme by 
@mire NV
 

 

Useful links

CTU in PragueCentral library of CTUAbout CTU Digital LibraryResourcesStudy and library skillsResearch support

Browse

All of DSpaceCommunities & CollectionsBy Issue DateAuthorsTitlesSubjectsThis CollectionBy Issue DateAuthorsTitlesSubjects

My Account

Login

České vysoké učení technické v Praze copyright © 2016 

DSpace software copyright © 2002-2016  Duraspace

Contact Us | Send Feedback
Theme by 
@mire NV