Zobrazit minimální záznam

Computational tool for optimal sizing of combined heat and power sources



dc.contributor.advisorKlein Vít
dc.contributor.authorMartin Lukeš
dc.date.accessioned2024-06-18T10:39:49Z
dc.date.available2024-06-18T10:39:49Z
dc.date.issued2024-06-11
dc.identifierKOS-1243608898405
dc.identifier.urihttp://hdl.handle.net/10467/114969
dc.description.abstractDiplomová práce se v teoretické části zabývá popisem kombinované výroby elektřiny a tepla, kogeneračních jednotek, porovnání se samostatnou výrobou elektřiny a tepla, návrhem kogenerační jednotky a ekonomickým zhodnocení investic. Tyto informace jsou pak využité v praktické části, která se zabývá tvorbou výpočetního nástroje pro dimenzování kogenerační jednotky. Praktická část obsahuje popis elektrické a tepelné spotřeby. Dále tu jsou popsány vybrané varianty a nástroj, který byl vytvořen ve Wolfram Mathematica. Spotřeby a parametry vybraných variant byly vloženy do nástroje a z nástroje jsme poté dostali technické výsledky. Ty byly v nástroji dále využity k ekonomickému zhodnocení. Dále zde jsou provedeny citlivostní analýzy vstupních parametrů.cze
dc.description.abstractThe theoretical part of the thesis deals with the description of combined production of electricity and heat, cogeneration units, comparison with separate production of electricity and heat, design of cogeneration unit and economic evaluation of investments. This information is then used in the practical part, which deals with the development of a calculation tool for sizing the cogeneration unit. The practical part contains a description of the electrical and thermal consumption. It also describes selected variants and the tool, which was developed in Wolfram Mathematica. The consumption and parameters of the selected variants were entered into the tool and the technical results were then obtained from the tool. These were further used in the tool for economic evaluation. In addition, sensitivity analyses of the input parameters are performed.eng
dc.publisherČeské vysoké učení technické v Praze. Vypočetní a informační centrum.cze
dc.publisherCzech Technical University in Prague. Computing and Information Centre.eng
dc.rightsA university thesis is a work protected by the Copyright Act. Extracts, copies and transcripts of the thesis are allowed for personal use only and at one?s own expense. The use of thesis should be in compliance with the Copyright Act http://www.mkcr.cz/assets/autorske-pravo/01-3982006.pdf and the citation ethics http://knihovny.cvut.cz/vychova/vskp.htmleng
dc.rightsVysokoškolská závěrečná práce je dílo chráněné autorským zákonem. Je možné pořizovat z něj na své náklady a pro svoji osobní potřebu výpisy, opisy a rozmnoženiny. Jeho využití musí být v souladu s autorským zákonem http://www.mkcr.cz/assets/autorske-pravo/01-3982006.pdf a citační etikou http://knihovny.cvut.cz/vychova/vskp.htmlcze
dc.subjectKombinovaná výroba elektřiny a teplacze
dc.subjectKogenerační jednotkacze
dc.subjectEkonomická kritériacze
dc.subjectWolfram Mathematicacze
dc.subjectSpalovací motorcze
dc.subjectCombined heat and powereng
dc.subjectCogeneration uniteng
dc.subjectEconomic criteriaeng
dc.subjectWolfram Mathematicaeng
dc.subjectCombustion engineeng
dc.titleVýpočetní nástroj pro optimální dimenzování zdroje kombinované výroby elektřiny a teplacze
dc.titleComputational tool for optimal sizing of combined heat and power sourceseng
dc.typediplomová prácecze
dc.typemaster thesiseng
dc.contributor.refereeŠváb Michal
theses.degree.disciplineElektroenergetikacze
theses.degree.grantorkatedra elektroenergetikycze
theses.degree.programmeElektrotechnika, energetika a managementcze


Soubory tohoto záznamu





Tento záznam se objevuje v následujících kolekcích

Zobrazit minimální záznam