ČVUT DSpace
  • Search DSpace
  • Čeština
  • Login
  • Čeština
  • Čeština
View Item 
  •   ČVUT DSpace
  • Czech Technical University in Prague
  • Faculty of Electrical Engineering
  • Department of Electromagnetic Field
  • Bachelor Theses - 13117
  • View Item
  • Czech Technical University in Prague
  • Faculty of Electrical Engineering
  • Department of Electromagnetic Field
  • Bachelor Theses - 13117
  • View Item
JavaScript is disabled for your browser. Some features of this site may not work without it.

Dielektrické parametry filamentů pro 3D tiskárny

Evaluating Dielectric Parameters of Filaments for 3D Printers

Type of document
bakalářská práce
bachelor thesis
Author
Jakub Mojzík
Supervisor
Hazdra Pavel
Opponent
Masopust Jiří
Study program
Elektronika a komunikace
Institutions assigning rank
katedra elektromagnetického pole



Rights
A university thesis is a work protected by the Copyright Act. Extracts, copies and transcripts of the thesis are allowed for personal use only and at one?s own expense. The use of thesis should be in compliance with the Copyright Act http://www.mkcr.cz/assets/autorske-pravo/01-3982006.pdf and the citation ethics http://knihovny.cvut.cz/vychova/vskp.html
Vysokoškolská závěrečná práce je dílo chráněné autorským zákonem. Je možné pořizovat z něj na své náklady a pro svoji osobní potřebu výpisy, opisy a rozmnoženiny. Jeho využití musí být v souladu s autorským zákonem http://www.mkcr.cz/assets/autorske-pravo/01-3982006.pdf a citační etikou http://knihovny.cvut.cz/vychova/vskp.html
Metadata
Show full item record
Abstract
Práce popisuje metodu určení dielektrických parametrů pomocí měření vlnovodnou sondou s otevřeným koncem a následné vyhodnocení porovnáním s daty ze simulace. Testovány byly celkem tři materiály běžně používané pro 3D tisk, kterými jsou ASA, PLA a PETG. Vzorky z těchto filamentů byly vyrobené vždy s plněním 15 % a 50 %. Z měření vychází, že při zvětšování plnění vzorků u všech materiálů roste permitivita a naopak klesá ztrátový činitel. Na výsledcích lze pozorovat významný vliv vnitřní struktury vzorků na měření. Zároveň byla vyzkoušena varianta měření, kdy se za měřený vzorek umístila vodivá deska. U této varianty ovšem nebylo možné rozpoznat rozdíly mezi vzorky vyrobenými z podobných materiálů. Všechna měření byla provedena na rozsahu frekvencí 4 GHz až 6 GHz. V článcích zkoumajících dielektrické parametry filamentů do 3D tiskáren se běžně provádí měření na vzorcích se 100% plněním. Na to navazuje tato práce měřením vzorků s nižším plněním.
 
The thesis describes a method of determination of dielectric parameters using open-ended waveguide probe measurement and subsequent evaluation by comparison with simulation data. A total of three materials commonly used for 3D printing, namely ASA, PLA and PETG, were tested. All samples made from these filaments were produced with 15% and 50% filling. The measurement shows that the permittivity of all materials increases and the loss factor decreases with increasing sample filling. The results show a significant influence of the internal structure of the samples on the measurements. In addition a measurement variant was tested where a conductive plate was placed behind the measured sample. However, it was not possible to detect differences between samples made from similar materials in this variant. All measurements were made at frequencies of 4 GHz to 6 GHz. In articles examining dielectric parameters of filaments for 3D printers, measurements on samples with 100% filling are commonly performed. This is followed by this thesis by measuring samples with lower filling.
 
URI
http://hdl.handle.net/10467/101246
View/Open
PLNY_TEXT (18.07Mb)
PRILOHA (9.850Mb)
POSUDEK (138.1Kb)
POSUDEK (623.4Kb)
Collections
  • Bakalářské práce - 13117 [131]

České vysoké učení technické v Praze copyright © 2016 

DSpace software copyright © 2002-2016  Duraspace

Contact Us | Send Feedback
Theme by 
@mire NV
 

 

Useful links

CTU in PragueCentral library of CTUAbout CTU Digital LibraryResourcesStudy and library skillsResearch support

Browse

All of DSpaceCommunities & CollectionsBy Issue DateAuthorsTitlesSubjectsThis CollectionBy Issue DateAuthorsTitlesSubjects

My Account

Login

České vysoké učení technické v Praze copyright © 2016 

DSpace software copyright © 2002-2016  Duraspace

Contact Us | Send Feedback
Theme by 
@mire NV