Tribologické chování 3D tištěného polymeru
Tribology behavior of 3D printed polymer
dc.contributor.advisor | Kronek Jakub | |
dc.contributor.author | Ivana Šetmaňuková | |
dc.date.accessioned | 2021-08-27T22:52:32Z | |
dc.date.available | 2021-08-27T22:52:32Z | |
dc.date.issued | 2021-08-27 | |
dc.identifier | KOS-1071242302905 | |
dc.identifier.uri | http://hdl.handle.net/10467/96895 | |
dc.description.abstract | Práce zjišťuje a porovnává otěrové vlastnosti 3D tištěného PEEKu a konvenčně vyrobeného PEEKu v oblasti biomechaniky. Vlastnosti jsou experimentálně otestovány na simulátoru v zatěžovacím cyklu pro obecný kloub. Proti PEEKovým jamkám se v simulátoru otíraly CoCrMo hlavice. Vyhodnoceny byly hmotnostní a objemové úbytky. 3D tištěný PEEK měl v obou vyhodnoceních menší úbytky materiálu vzhledem ke konvenčnímu PEEKu. Tato práce poskytla experimentální výsledky pro 3D tištěný PEEK, které dosud nebyly publikovány a doporučuje strukturu 3D tištěných polymerů i 3D tisk jako technologii využitelnou pro artikulující náhrady. | cze |
dc.description.abstract | The diploma thesis determines and compares the wear properties of 3D printed PEEK and conventionally produced PEEK in biomechanics. The properties are experimentally tested on knee joint simulator with CoCrMo head against PEEK socket for a period of 250 000 cycles. The properties were evaluated according to linear and volumetric wear. The wear rate of PEEK was higher than of 3D printed PEEK. This work provided experimental results for 3D printed PEEK, which has not been published yet and recommends the structure of 3D printed polymers and 3D printing as a technology usable for joint replacement. | eng |
dc.publisher | České vysoké učení technické v Praze. Vypočetní a informační centrum. | cze |
dc.publisher | Czech Technical University in Prague. Computing and Information Centre. | eng |
dc.rights | A university thesis is a work protected by the Copyright Act. Extracts, copies and transcripts of the thesis are allowed for personal use only and at one?s own expense. The use of thesis should be in compliance with the Copyright Act http://www.mkcr.cz/assets/autorske-pravo/01-3982006.pdf and the citation ethics http://knihovny.cvut.cz/vychova/vskp.html | eng |
dc.rights | Vysokoškolská závěrečná práce je dílo chráněné autorským zákonem. Je možné pořizovat z něj na své náklady a pro svoji osobní potřebu výpisy, opisy a rozmnoženiny. Jeho využití musí být v souladu s autorským zákonem http://www.mkcr.cz/assets/autorske-pravo/01-3982006.pdf a citační etikou http://knihovny.cvut.cz/vychova/vskp.html | cze |
dc.subject | PEEK | cze |
dc.subject | polyether ether keton | cze |
dc.subject | 3D tisk | cze |
dc.subject | biotribologie | cze |
dc.subject | otěr | cze |
dc.subject | hmotnostní úbytek | cze |
dc.subject | objemový úbytek | cze |
dc.subject | PEEK | eng |
dc.subject | polyether ether ketone | eng |
dc.subject | 3D print | eng |
dc.subject | biotribilogy | eng |
dc.subject | wear | eng |
dc.subject | linear wear | eng |
dc.subject | volumetric wear | eng |
dc.title | Tribologické chování 3D tištěného polymeru | cze |
dc.title | Tribology behavior of 3D printed polymer | eng |
dc.type | diplomová práce | cze |
dc.type | master thesis | eng |
dc.contributor.referee | Chlup Hynek | |
theses.degree.discipline | Biomechanika | cze |
theses.degree.grantor | ústav mechaniky, biomechaniky a mechatroniky | cze |
theses.degree.programme | Aplikované vědy ve strojním inženýrství | cze |
Soubory tohoto záznamu
Tento záznam se objevuje v následujících kolekcích
-
Diplomové práce - 12105 [212]