Stanovení křivek mezní tvářitelnosti pomocí zkoušky tahem a systému ARAMIS
Determination of forming limit curves according to tensile test and Aramis system
dc.contributor.advisor | Tatíček František | |
dc.contributor.author | Pavel Krejsa | |
dc.date.accessioned | 2020-08-20T22:52:41Z | |
dc.date.available | 2020-08-20T22:52:41Z | |
dc.date.issued | 2020-08-20 | |
dc.identifier | KOS-985499503805 | |
dc.identifier.uri | http://hdl.handle.net/10467/89587 | |
dc.description.abstract | Tato diplomová práce je zaměřena na stanovení křivek mezních deformací pomocí tahové zkoušky a systému ARAMIS. Tyto křivky nám udávají zásobu plasticity a vymezují velikost deformace, kterou materiál vydrží, než dojde k porušení. Teoretická část práce se zabývá tvářením, zejména pak tvářitelností a činiteli, které ji ovlivňují. Dále je zde seznámení s tahovou zkouškou. Popsány jsou rovněž optické systémy pro snímání deformací, tvorba a význam FLD včetně činitelů, kteří ovlivňují polohu křivek mezních deformací. V experimentální části je práce zaměřena na zkoušku vzorků z oceli DX57D. Porovnává se vliv rychlosti zatěžování a směru válcování na polohu křivek mezních deformací. Snímání deformací bylo zajištěno optickými systémy ARAMIS a ARGUS. Výstupem je grafické porovnání těchto vlivů a porovnání obou systémů. | cze |
dc.description.abstract | This thesis focuses on the determination of the curves of limit deformations using the tensile test and the ARAMIS system. These curves give us a supply of plasticity and define the size of the deformation that the material can withstand before the violation. The theoretical part of the thesis deals with forming, especially the formability and factors that influence it. There is also an introduction to the tensile test. Optical systems for sensing deformations, the formation and importance of FLD, including factors that affect the position of the curves of limit deformations, are also described. In the experimental part, the work is focused on the testing of samples made of DX57D steel. The effect of the load rate and the direction of rolling on the position of the curves of the limit deformations are compared. Deformation sense was provided by ARAMIS and ARGUS optical systems. The output is a graphical comparison of these influences and a comparison of the two systems. | eng |
dc.publisher | České vysoké učení technické v Praze. Vypočetní a informační centrum. | cze |
dc.publisher | Czech Technical University in Prague. Computing and Information Centre. | eng |
dc.rights | A university thesis is a work protected by the Copyright Act. Extracts, copies and transcripts of the thesis are allowed for personal use only and at one?s own expense. The use of thesis should be in compliance with the Copyright Act http://www.mkcr.cz/assets/autorske-pravo/01-3982006.pdf and the citation ethics http://knihovny.cvut.cz/vychova/vskp.html | eng |
dc.rights | Vysokoškolská závěrečná práce je dílo chráněné autorským zákonem. Je možné pořizovat z něj na své náklady a pro svoji osobní potřebu výpisy, opisy a rozmnoženiny. Jeho využití musí být v souladu s autorským zákonem http://www.mkcr.cz/assets/autorske-pravo/01-3982006.pdf a citační etikou http://knihovny.cvut.cz/vychova/vskp.html | cze |
dc.subject | Tváření | cze |
dc.subject | tvářitelnost | cze |
dc.subject | tahová zkouška | cze |
dc.subject | křivky mezních deformací | cze |
dc.subject | optické měřící systémy | cze |
dc.subject | systém ARAMIS | cze |
dc.subject | systém ARGUS | cze |
dc.subject | ocel DX57D | cze |
dc.subject | Forming | eng |
dc.subject | formability | eng |
dc.subject | tensile test | eng |
dc.subject | forming limit curves | eng |
dc.subject | optical measuring systems | eng |
dc.subject | Aramis system | eng |
dc.subject | Argus system | eng |
dc.subject | steel DX57D | eng |
dc.title | Stanovení křivek mezní tvářitelnosti pomocí zkoušky tahem a systému ARAMIS | cze |
dc.title | Determination of forming limit curves according to tensile test and Aramis system | eng |
dc.type | diplomová práce | cze |
dc.type | master thesis | eng |
dc.contributor.referee | Valeš Michal | |
theses.degree.discipline | Výrobní a materiálové inženýrství | cze |
theses.degree.grantor | ústav strojírenské technologie | cze |
theses.degree.programme | Strojní inženýrství | cze |
Soubory tohoto záznamu
Tento záznam se objevuje v následujících kolekcích
-
Diplomové práce - 12133 [217]