Návrh sondy pro měření hrubé vodní disperze v parních turbínách
A new probe design for the measurement of the coarse droplets in steam turbine
dc.contributor.advisor | Bartoš Ondřej | |
dc.contributor.author | Marek Nedoma | |
dc.date.accessioned | 2019-06-20T22:54:09Z | |
dc.date.available | 2019-06-20T22:54:09Z | |
dc.date.issued | 2019-06-20 | |
dc.identifier | KOS-883223159605 | |
dc.identifier.uri | http://hdl.handle.net/10467/83563 | |
dc.description.abstract | Diplomová práce se zabývá erozí parních lopatek a návrhem sondy pro měření hrubé vodní disperze v parních turbínách. První část teoreticky popisuje mechanizmy eroze parních lopatek v posledních stupních parních turbín srážkami vodních kapek s povrchem lopatky. Druhá část se věnuje konstrukčnímu návrhu sondy, která se v praxi použije pro záznam distribuce vodních kapek v prostoru parní turbíny. Koncept sondy je v kritických místech ověřen pevnostními a kinematickými výpočty. 3D model sondy je vyvíjen pomocí programu Autodesk Inventor. Součástí druhé části je zároveň praktické měření kalibrace endocentrického objektivu kamery, pro jehož zhodnocení byl využit program MATLAB a popis instalace a testování lineárního servomotoru. | cze |
dc.description.abstract | This diploma thesis deals with turbine blade erosion and a new probe design for the measurements of coarse droplets progression in the steam turbines. The first section theoretically describes the mechanisms of water droplets erosion and their impact on the turbine blade surfaces in the last-stages of steam turbine by interaction between the water droplets and the blade surface. The second section is concerned with the designing of a new probe model which would be in practice used to record water droplet distribution inside the steam turbine. Probe structural design is tested on strength using strength and kinematics calculations in the critical areas. The 3D probe model is developed in the Autodesk Inventor software. Practical endocentric lenses calibration is also a part of the second section. Calibration was evaluated in the MATLAB software. At the end of this part a linear servomotor installation and testing are mentioned. | eng |
dc.publisher | České vysoké učení technické v Praze. Vypočetní a informační centrum. | cze |
dc.publisher | Czech Technical University in Prague. Computing and Information Centre. | eng |
dc.rights | A university thesis is a work protected by the Copyright Act. Extracts, copies and transcripts of the thesis are allowed for personal use only and at one?s own expense. The use of thesis should be in compliance with the Copyright Act http://www.mkcr.cz/assets/autorske-pravo/01-3982006.pdf and the citation ethics http://knihovny.cvut.cz/vychova/vskp.html | eng |
dc.rights | Vysokoškolská závěrečná práce je dílo chráněné autorským zákonem. Je možné pořizovat z něj na své náklady a pro svoji osobní potřebu výpisy, opisy a rozmnoženiny. Jeho využití musí být v souladu s autorským zákonem http://www.mkcr.cz/assets/autorske-pravo/01-3982006.pdf a citační etikou http://knihovny.cvut.cz/vychova/vskp.html | cze |
dc.subject | Parní turbína | cze |
dc.subject | návrh sondy | cze |
dc.subject | vodní disperze | cze |
dc.subject | kinematika | cze |
dc.subject | eroze lopatek parní turbíny | cze |
dc.subject | kalibrace endocentrického objektivu | cze |
dc.subject | MATLAB | cze |
dc.subject | Autodesk Inventor | cze |
dc.subject | Steam turbine | eng |
dc.subject | probe design | eng |
dc.subject | coarse droplets | eng |
dc.subject | kinematics | eng |
dc.subject | turbine blade erosion | eng |
dc.subject | endocentric lenses calibration | eng |
dc.subject | MATLAB | eng |
dc.subject | Autodesk Inventor | eng |
dc.title | Návrh sondy pro měření hrubé vodní disperze v parních turbínách | cze |
dc.title | A new probe design for the measurement of the coarse droplets in steam turbine | eng |
dc.type | diplomová práce | cze |
dc.type | master thesis | eng |
dc.contributor.referee | Kolovratník Michal | |
theses.degree.discipline | Energetika | cze |
theses.degree.grantor | ústav energetiky | cze |
theses.degree.programme | Strojní inženýrství | cze |
Soubory tohoto záznamu
Tento záznam se objevuje v následujících kolekcích
-
Diplomové práce - 12115 [205]