Zobrazit minimální záznam

Dry machining of titanium



dc.contributor.advisorPitrmuc Zdeněk
dc.contributor.authorBrodský Petr
dc.date.accessioned2019-02-20T10:50:33Z
dc.date.available2019-02-20T10:50:33Z
dc.date.issued2018-08-31
dc.identifierKOS-695599872105
dc.identifier.urihttp://hdl.handle.net/10467/79961
dc.description.abstractTato bakalářská práce shrnuje základní informace o titanu, jeho slitinách a specifika obrábění těchto slitin. Důraz je kladen především na frézování. Rešeršní část práce se zaměřuje na výrobu titanu a rozdělení titanových slitin. Následující část je věnována především technologickým vlastnostem titanu a jeho slitinách. V další části práce jsou uvedeny obecné zásady frézování těchto slitin, nejnovější trendy a rozbor současné nabídky obráběcích nástrojů. Praktická část popisuje návrh a přípravu experimentu technologické zkoušky, jehož cílem bude zkoumání řezných sil v závislosti na úhlu čela vyměnitelné břitové destičky a jejího opotřebení.cze
dc.description.abstractThis bachelor thesis summarizes basic information about titanium, its alloys and the specifics of machining of these alloys. Emphasis is put primarily on milling. The research part of this thesis focuses on the production of titanium and distribution of titanium alloys. The following part is devoted mainly to technological properties of titanium and alloys. The next part presents general principles of milling previously described alloys, the latest trends and analysis of the current offer of machining tools. The practical part describes proposal and preparation of an experiment technological test, which aims to examine the cutting forces depending on the rake angle of the indexable insert and its wear.eng
dc.language.isoCZE
dc.publisherČeské vysoké učení technické v Praze. Vypočetní a informační centrum.cze
dc.publisherCzech Technical University in Prague. Computing and Information Centre.eng
dc.rightsA university thesis is a work protected by the Copyright Act. Extracts, copies and transcripts of the thesis are allowed for personal use only and at one?s own expense. The use of thesis should be in compliance with the Copyright Act http://www.mkcr.cz/assets/autorske-pravo/01-3982006.pdf and the citation ethics http://knihovny.cvut.cz/vychova/vskp.htmleng
dc.rightsVysokoškolská závěrečná práce je dílo chráněné autorským zákonem. Je možné pořizovat z něj na své náklady a pro svoji osobní potřebu výpisy, opisy a rozmnoženiny. Jeho využití musí být v souladu s autorským zákonem http://www.mkcr.cz/assets/autorske-pravo/01-3982006.pdf a citační etikou http://knihovny.cvut.cz/vychova/vskp.htmlcze
dc.subjectTitan,slitiny titanu,vlastnosti titanu,frézování,frézovací nástroje,úhel čelacze
dc.subjectTitanium,titanium alloys,properties of titanium,milling,milling tools,rake angleeng
dc.titleSuché obrábění titanových slitincze
dc.titleDry machining of titaniumeng
dc.typebakalářská prácecze
dc.typebachelor thesiseng
dc.date.accepted2018-09-05
dc.contributor.refereeMikeš Petr
theses.degree.disciplinebez oborucze
theses.degree.grantorústav technologie obrábění, projektování a metrologiecze
theses.degree.programmeTeoretický základ strojního inženýrstvícze


Soubory tohoto záznamu




Tento záznam se objevuje v následujících kolekcích

Zobrazit minimální záznam