Navržení postupu svařování při opravách síta alkalizačního lisu.
Design of the welding process for repair of the alkalization press sieve.
Typ dokumentu
diplomová prácemaster thesis
Autor
Vazač Jan
Vedoucí práce
Kovanda Karel
Oponent práce
Brenner Otakar
Studijní obor
Výrobní a materiálové inženýrstvíStudijní program
Strojní inženýrstvíInstituce přidělující hodnost
ústav strojírenské technologiePráva
A university thesis is a work protected by the Copyright Act. Extracts, copies and transcripts of the thesis are allowed for personal use only and at one?s own expense. The use of thesis should be in compliance with the Copyright Act http://www.mkcr.cz/assets/autorske-pravo/01-3982006.pdf and the citation ethics http://knihovny.cvut.cz/vychova/vskp.htmlVysokoškolská závěrečná práce je dílo chráněné autorským zákonem. Je možné pořizovat z něj na své náklady a pro svoji osobní potřebu výpisy, opisy a rozmnoženiny. Jeho využití musí být v souladu s autorským zákonem http://www.mkcr.cz/assets/autorske-pravo/01-3982006.pdf a citační etikou http://knihovny.cvut.cz/vychova/vskp.html
Metadata
Zobrazit celý záznamAbstrakt
Práce se zaměřuje na problematiku vzniku a šíření trhlin korozivzdorných sít, které se objevují během provozu alkalizačního lisu, na svařování a renovaci těchto sít a jimi pokrytých lisovacích válců. V teoretické části se zabývá vývojem a historií technologie svařování, jejím rozdělením a terminologií svaru. Dále se práce zabývá korozivzdornými materiály, jejich rozdělením a chemickým složením, druhy korozí a výrobě a zpracování celulózy. V praktické části jsou veškeré informace o lisu, na kterém byla práce řešena. Dále jsou shrnuty požadavky práce a popsána problematika vzniku a šíření trhlin na zmíněných sítech. Bylo provedeno několik analýz a měření, která vedla k určení vhodnosti základních a přídavných materiálů. Na základě těchto výsledků a porovnání byly doporučeny změny některých materiálů a postupů či technologií. Pro zajištění ideálních výsledků práce bylo doporučeno i na dále mapovat problematiku vzniku trhlin po změně vstupních parametrů, veškeré informace zapisovat a statisticky vyhodnotit optimální řešení další renovace lisu. The main focus of this diploma thesis is the origin and spread of the corrosion cracks that occur during the operation of alkalization press on stainless sieves, the welding technology and renovation these sieves and with them covered press roll. The theoretical part deal with development and history of welding technology, its distribution and terminology of welding. Further, the thesis deals with corrosion resistant materials, their selection and chemical composition, types of corrosion and the fabrication and treatment of cellulose. In practical part of this work there are all information about the press on which is the work based. Further, requirements of the work are summarized and the problems of crack formation and spreading on mentioned sieves is described. Several analyzes and measurements have been made, carried out determination for suitability of the basic material and filler materials. Based on these results and comparisons, changes to some materials and procedures or technologies have been recommended. In order to ensure ideal work results, it was recommended to further map the problem of cracks after changing the input parameters, to write down this information and statistically evaluate the optimal solution for further refurbishment of the press.
Kolekce
- Diplomové práce - 12133 [236]