Procházení Acta Polytechnica. 2019, vol. 59 dle data publikování
Zobrazují se záznamy 41-60 z 60
-
ADSORPTION OF CATIONIC DYE FROM AQUEOUS SOLUTION USING COMPOSITE CHICKEN EGGSHELL - ANTHILL CLAY: OPTIMIZATION OF ADSORBENT PREPARATION CONDITIONS
(České vysoké učení technické v PrazeCzech Technical University in Prague, 2019)A composite adsorbent was prepared from anthill and eggshell mixture, using an incipient wetness impregnation method and it was used for an adsorption of cationic dye (methylene blue, MB) from an aqueous solution. The ... -
GENERAL CALCULATION OF WINDING FACTOR FOR MULTI-PHASE/-LAYER ELECTRICAL MACHINES IRRESPECTIVE OF POLES NUMBER
(České vysoké učení technické v PrazeCzech Technical University in Prague, 2019)In this paper, a method to calculate the winding factor by only considering stator parameters without the rotor ones is developed. This is interesting because it allows the separation of the stator and rotor design, unlike ... -
STUDY OF SYNTHETIC DYE REMOVAL USING FENTON/TiO2, FENTON/UV, AND FENTON/TiO2/UV METHODS AND THE APPLICATION TO JUMPUTAN FABRIC WASTEWATER
(České vysoké učení technické v PrazeCzech Technical University in Prague, 2019)Synthetic dyes were commonly used in textile industries such as Jumputan fabric industries in South Sumatera. Most of these industries were categorized as a home industry without a wastewater treatment plant, so the ... -
ANALYSIS OF THE PROPERTIES OF AW2099 ALUMINIUM-LITHIUM ALLOY WELDED BY LASER BEAM WITH AW5087 ALUMINIUM-MAGNESIUM FILLER MATERIAL
(České vysoké učení technické v PrazeCzech Technical University in Prague, 2019)EN AW2099 aluminium lithium alloy, 2.0mm in thickness, was used as an experimental material. EN AW2099 belongs to the 3rd generation of aluminium lithium alloys. The third generation was developed to improve the disadvantages ... -
FABRICATION OF Mg-Zn-Al HYDROTALCITE AND ITS APPLICATION FOR Pb<sup>2+</sup> REMOVAL
(České vysoké učení technické v PrazeCzech Technical University in Prague, 2019)The fabrication of Mg-Zn-Al Hydrotalcite (HT) was carried out by the co-precipitation method at various molar ratios. The Mg-Zn-Al HT compound at the optimum molar ratio was then calcined to determine the effect of calcination ... -
DEFLECTIONS AND FREQUENCY ANALYSIS IN THE MILLING OF THIN-WALLED PARTS WITH VARIABLE LOW STIFFNESS
(České vysoké učení technické v PrazeCzech Technical University in Prague, 2019)The disadvantage of the geometry of thin-walled parts, in terms of processing, is the low ability to resist static and dynamic loads. It is caused by the elastic deformation of elements with a low stiffness. Modelling ... -
COMPARATIVE STUDY AND EMPIRICAL MODELLING OF PULVERIZED COCONUT SHELL, PERIWINKLE SHELL AND PALM KERNEL SHELL AS A POZZOLANS IN CONCRETE
(České vysoké učení technické v PrazeCzech Technical University in Prague, 2019)Infrastructural development across the world is fast growing due to the rapid growth in population. This has resulted in consequently creating an increase in the demand for construction materials, especially cement. This ... -
MODEL-BASED SECURITY ANALYSIS OF FPGA DESIGNS THROUGH REINFORCEMENT LEARNING
(České vysoké učení technické v PrazeCzech Technical University in Prague, 2019)Finding potential security weaknesses in any complex IT system is an important and often challenging task best started in the early stages of the development process. We present a method that transforms this task for FPGA ... -
3-D MODELING OF HEAT AND MASS TRANSFER PROCESS DURING THE COMBUSTION OF SOLID FUEL IN A SWIRL FURNACE
(České vysoké učení technické v PrazeCzech Technical University in Prague, 2019)In this work, a comprehensive study of thermal processes and aerodynamic and concentration characteristics of the combustion chamber of the boiler BKZ-75 of the Shakhtinskaya thermal power plant (Kazakhstan) are presented. ... -
GAS-PUFF TARGET FOR LASER-PRODUCING PLASMA SXR SOURCE
(České vysoké učení technické v PrazeCzech Technical University in Prague, 2019)Mass density spatial distributions of selected gas-puff targets have been determined by radiography, using quasi-monochromatic radiation at a wavelength of 13 nm. Results of spatial distributions of mass densities at various ... -
CZECH WW2 CONCRETE FORTIFICATIONS: CORROSION PROCESSES AND REMEDIATION METHOD BASED ON CRYSTALLIZING COATING
(České vysoké učení technické v PrazeCzech Technical University in Prague, 2019)Concrete is a relatively new structural material, hence the remediation of concrete structures is very rare. There are a lot of concrete fortifications in the Czech Republic, which were built just before WW2. These bunkers ... -
WAAM TECHNOLOGY OPTIMIZED BY OFF-LINE 3D ROBOT SIMULATION
(České vysoké učení technické v PrazeCzech Technical University in Prague, 2019)WAAM (Wire + Arc Additive Manufacturing) is an alternative additive technology that combines an electric arc as a heat source, filler material in the form of a wire for welding and cladding individual weld passes so as to ... -
3D DIGITAL RECONSTRUCTION BASED ON ARCHIVED TERRESTRIAL PHOTOGRAPHS FROM METRIC CAMERAS
(České vysoké učení technické v PrazeCzech Technical University in Prague, 2019)The paper deals with the possibilities and limitations of the image processing of digitalized terrestrial photographs from analogue metric cameras. By the end of the 20th century, analogue metric cameras such as Zeiss UMK ... -
COMMON CROSSING CONDITION MONITORING WITH ON BOARD INERTIAL MEASUREMENTS
(České vysoké učení technické v PrazeCzech Technical University in Prague, 2019)A railway turnout is an element of the railway infrastructure that influences the reliability of a railway traffic operation the most. The growing necessity for the reliability and availability in the railway transportation ... -
THE CHARACTERISTICS OF Al-Si COATING ON STEEL 22MnB5 DEPENDING ON THE HEAT TREATMENT
(České vysoké učení technické v PrazeCzech Technical University in Prague, 2019)The coating on the 22MnB5 steel is intended to protect it against oxidation during the forming process. This steel is hot-pressed. A preheating before the pressing and subsequent hardening in the tool affects the properties ... -
MECHANICAL PROPERTIES OF RAMMED EARTH WITH RESPECT TO CLAY MIXTURE COMPOSITION
(České vysoké učení technické v PrazeCzech Technical University in Prague, 2019)Unfired earth is a traditional building material, but it is less used than other building materials, such as concrete or steel. But the use of unfired earth is experiencing a renaissance. ammed earth is a type of unfired ... -
A COMPARATIVE STUDY OF DATA-DRIVEN MODELING METHODS FOR SOFT-SENSING IN UNDERGROUND COAL GASIFICATION
(České vysoké učení technické v PrazeCzech Technical University in Prague, 2019)Underground coal gasification (UCG) is a technological process, which converts solid coal into a gas in the underground, using injected gasification agents. In the UCG process, a lot of process variables can be measurable ... -
HEAT FLUX JUMP METHOD AS A POSSIBILITY OF CONTACTLESS MEASUREMENT OF LOCAL HEAT TRANSFER COEFFICIENTS
(České vysoké učení technické v PrazeCzech Technical University in Prague, 2019)This article deals with the derivation of the temperature response of the finite thickness wall, which is heated by heat flow, as a possibility to measure the local values of the heat transfer coefficient with a very high ... -
A MULTIPHASE FLOW LOOP DESIGN FOR INVESTIGATING THE PARTIAL PHASE SEPARATION IN A PIPE TEE
(České vysoké učení technické v PrazeCzech Technical University in Prague, 2019)This article presents a design and commissioning of a multiphase flow loop, which was developed for scrutinizing the partial phase separation characteristics of pipe Tees. Its length is 9m and its primary diameter is 0.078m ... -
EVALUATING SHEAR STRENGTH OF SAND- GGBFS BASED GEOPOLYMER COMPOSITE MATERIAL
(České vysoké učení technické v PrazeCzech Technical University in Prague, 2019)Geopolymer has been emerging as a novel and sustainable replacement for the traditional soil improvement materials, such as ordinary Portland cement OPC and lime, which have severe environmental impacts. In this paper, a ...