Nedávno přidané

Zobrazují se záznamy 1-14 z 14

    • ANALYSIS OF PARAMETERS AFFECTING THE QUALITY OF A CUTTING MACHINE 

      Autor: Onderová , Iveta; Šooš , Lubomír
      (České vysoké učení technické v PrazeCzech Technical University in Prague, 2014)
      The quality of cutting machines is affected by several factors that can be directly or indirectly influenced by manufacturers, technicians and users of machine tools. The most critical qualitative evaluation parameters of ...
    • DESIGN THEORY FOR THE PRESSING CHAMBER IN THE SOLID BIOFUEL PRODUCTION PROCESS 

      Autor: Kováčová , Monika; Matúš , Miloš; Križan , Peter; Beniak , Juraj
      (České vysoké učení technické v PrazeCzech Technical University in Prague, 2014)
      The quality of a high-grade solid biofuel depends on many factors, which can be divided into three main groups - material, technological and structural. The main focus of this paper is on observing the influence of structural ...
    • CURRENT WAYS TO HARVEST ENERGY USING A COMPUTER MOUSE 

      Autor: Horvat , Frantisek; Cekan , Michal; Soltes , Lukas; Biath , Peter; Hucko , Branislav; Jedinak , Igor
      (České vysoké učení technické v PrazeCzech Technical University in Prague, 2014)
      This paper deals with the idea of an energy harvesting (EH) system that uses the mechanical energy from finger presses on the buttons of a computer mouse by means of a piezomaterial (PVF2). The piezomaterial is placed in ...
    • THE EFFECT OF ADDING HYDROGEN ON THE PERFORMANCE AND THE CYCLIC VARIABILITY OF A SPARK IGNITION ENGINE POWERED BY NATURAL GAS 

      Autor: Chríbik , Andrej; Polóni , Marián; Lach , Ján; Ragan , Branislav
      (České vysoké učení technické v PrazeCzech Technical University in Prague, 2014)
      This paper deals with the influence of blending hydrogen (from 0 to 50% vol.) on the parameters and the cyclic variability of a Lombardini LGW702 combustion engine powered by natural gas. The experimental measurements were ...
    • LABORATORY EQUIPMENT FOR AUTOTHERMAL REFORMING OF ORGANIC MATTER IN SUPERCRITICAL WATER 

      Autor: Gajdoš , Matúš
      (České vysoké učení technické v PrazeCzech Technical University in Prague, 2014)
      The ability of water to dissolve organic substances is very limited. However, its ability to dissolve them changes if pressure and temperature values reach the so-called critical point (p = 22.06MPa, T = 373.95 °C). Fluid ...
    • SIZE ANALYSIS OF SOLID PARTICLES AT THE EXPERIMENTAL DEVICE FOR MULTISTAGE BIOMASS COMBUSTION 

      Autor: Hrnčířová , Michaela; Špiláček , Michal; Pospíšil , Jiří
      (České vysoké učení technické v PrazeCzech Technical University in Prague, 2014)
      This paper presents the results of an analysis of ash content particles produced in biomass combustion at an experimental device. The main parts of the device are: the water heater, the gasifying chamber, the air preheater, ...
    • AUTOMATIC BIOMASS BOILER WITH AN EXTERNAL THERMOELECTRIC GENERATOR 

      Autor: Brázdil , Marian; Šnajdárek , Ladislav; Kracík , Petr; Pospíšil , Jirí
      (České vysoké učení technické v PrazeCzech Technical University in Prague, 2014)
      This paper presents the design and test results of an external thermoelectric generator that utilizes the waste heat from a small-scale domestic biomass boiler with nominal rated heat output of 25 kW. The low-temperature ...
    • STABILIZATION TIME AS AN IMPORTANT PARAMETER AFTER DENSIFICATION OF SOLID BIOFUELS 

      Autor: Križan , Peter; Matúš , Miloš; Beniak , Juraj; Kováčová , Monika
      (České vysoké učení technické v PrazeCzech Technical University in Prague, 2014)
      The aim of this paper is to present some preliminary results from experimental research on the densification process of solid high-grade biofuels. The findings presented in this paper contribute to an investigation of the ...
    • THE OPERATING LOAD OF A DISINTEGRATION MACHINE 

      Autor: Beniak , Juraj; Križan , Peter; Matúš , Miloš; Kováčová , Monika
      (České vysoké učení technické v PrazeCzech Technical University in Prague, 2014)
      The process of disintegration is affected by a large number of operating and design parameters which have not previously been described in detail. This paper discusses the effect of the disintegrative surface area on the ...
    • THE INFLUENCE OF SIZE FRACTION ON THE COMPRESSIBILITY OF PINE SAWDUST AND THE EFFECTIVENESS CRITERION FOR DENSIFICATION 

      Autor: Matúš , Miloš; Križan , Peter; Kováčová , Monika; Beniak , Juraj
      (České vysoké učení technické v PrazeCzech Technical University in Prague, 2014)
      Particulate matter from biomass, e.g. wood sawdust, is very diverse. The basic parameter describing the densification process of particulate matter is its compressibility, quantified by the coefficient of compressibility. ...
    • SPECIFIC EMISSIONS FROM BIOMASS COMBUSTION 

      Autor: Skopec , Pavel; Hrdlička , Jan; Kaválek , Michal
      (České vysoké učení technické v PrazeCzech Technical University in Prague, 2014)
      This paper deals with determining the specific emissions from the combustion of two kinds of biomass fuels in a small-scale boiler. The tested fuels were pellets made of wood and pellets made of rape plant straw. In order ...
    • EXPERIMENTAL VERIFICATION OF THE STRUCTURAL AND TECHNOLOGICAL PARAMETERS OF THE PKS 

      Autor: Onderová , Iveta; Kolláth , Ludovít; Ploskuňáková , Lucia
      (České vysoké učení technické v PrazeCzech Technical University in Prague, 2014)
      This paper presents the theoretical design for experimental verification of the structural and technological parameters of the Parallel Kinematic Structure. The experimental equipment was developed at the Faculty of ...
    • NOx PREDICTION FOR FBC BOILERS USING EMPIRICAL MODELS 

      Autor: Štefanica , Jiří; Hrdlička , Jan
      (České vysoké učení technické v PrazeCzech Technical University in Prague, 2014)
      Reliable prediction of NOx emissions can provide useful information for boiler design and fuel selection. Recently used kinetic prediction models for FBC boilers are overly complex and require large computing capacity. ...
    • TECHNICAL AND ECONOMIC OPTIMIZATION OF COGENERATION TECHNOLOGY USING COMBUSTION AND GASIFICATION 

      Autor: Lisý , Martin; Baláš , Marek; Špiláček , Michal; Skála , Zdenek
      (České vysoké učení technické v PrazeCzech Technical University in Prague, 2014)
      This paper presents the technical and economic optimization of new microcogeneration technology with biomass combustion or biomass gasification used for cogeneration of electrical energy and heat for a 200 kW unit. During ...