Now showing items 1-20 of 24

    • An Application of the Individual Channel Analysis and Design Approach to Control of a Two-input Two-output Coupled-tanks System 

      Author: Murray-Smith , David J.
      (České vysoké učení technické v PrazeCzech Technical University in Prague, 2012)
      Frequency-domain methods have provided an established approach to the analysis and design of single-loop feedback control systems in many application areas for many years. Individual Channel Analysis and Design (ICAD) is ...
    • Replacing Natural Gas by Biogas — Determining the Bacterial Contamination of Biogas by PCR 

      Author: Čermáková , Jiřina; Mrázek , Jakub; Fliegerová , Kateřina; Tenkrát , Daniel
      (České vysoké učení technické v PrazeCzech Technical University in Prague, 2012)
      A promising way of using biogas is to upgrade it to natural gas, which is referred to as Substitute Natural Gas (SNG) or biomethane. Biomethane, or biogas, is produced by biological processes of harnessing the ability of ...
    • A Pulverized Coal-Fired Boiler Optimized for Oxyfuel Combustion Technology 

      Author: Dlouhý , Tomáš; Dupal , Tomáš; Dlouhý , Jan
      (České vysoké učení technické v PrazeCzech Technical University in Prague, 2012)
      This paper presents the results of a study on modifying a pulverized coal-fired steam boiler in a 250 MWe power plant for oxygen combustion conditions. The entry point of the study is a boiler that was designed for standard ...
    • Lifetime Assessment of a Steam Pipeline 

      Author: Janovec , Jiří; Poláchová , Daniela; Junek , Michal
      (České vysoké učení technické v PrazeCzech Technical University in Prague, 2012)
      The aim of this paper is to design a method for assessing the life of steam pipes for Czech power plants. The most widely-used material in Czech power plants is steel 15 128. Our findings may also be applied for international ...
    • Application of Induction Heating for Brazing Parts of Solar Collectors 

      Author: Demianová , Kristína; Ožvold , Milan; Turňa , Milan
      (České vysoké učení technické v PrazeCzech Technical University in Prague, 2012)
      This paper reports on the application of induction heating for brazing parts of solar collectors made of Al alloys. The tube-flange joint is a part of the collecting pipe of a solar collector. The main task was to design ...
    • Energy Accumulation by Hydrogen Technologies 

      Author: Čermáková , Jiřina; Doucek , Aleš; Polák , Lukáš
      (České vysoké učení technické v PrazeCzech Technical University in Prague, 2012)
      Photovoltaic power plants as a renewable energy source have been receiving rapidly growing attention in the Czech Republic and in the other EU countries. This rapid development of photovoltaic sources is having a negative ...
    • New Abrasive Materials and Their Influence on the Surface Quality of Bearing Steel After Grinding 

      Author: Jusko , Ondrej
      (České vysoké učení technické v PrazeCzech Technical University in Prague, 2012)
      This paper focuses on the influence of various types of abrasive grains on cutting properties during the grinding process for bearing steel. In this experiment, not only conventional super-hard abrasive materials but also ...
    • Laser Cutting of Materials of Various Thicknesses 

      Author: Grepl , Martin; Pagáč , Marek; Petrů , Jana
      (České vysoké učení technické v PrazeCzech Technical University in Prague, 2012)
      Thise paper deals with the application of laser technology and optimizing the parameters for cutting nickel alloy. The theoretical part of the paper describes various types of lasers, their principles and usage. The ...
    • Checking the Geometric Accuracy of a Machine Tool for Selected Geometric Parameters 

      Author: Janásek , Adam; Čep , Robert; Brychta , Josef
      (České vysoké učení technické v PrazeCzech Technical University in Prague, 2012)
      This paper deals with the control parameters for selected geometric accuracy measurements for a machine tool. The parameters were needed after a refurbished milling machine was purchased. After setting up the machine, it ...
    • Determination of Uncertainties for Correlated Input Quantities by the Monte Carlo Method 

      Author: Goliaš , Marcel; Palenčár , Rudolf
      (České vysoké učení technické v PrazeCzech Technical University in Prague, 2012)
      This paper presents the calculation of the uncertainty for distribution propagation by the Monte Carlo method for a measurement model with one output quantity. The procedure is shown on the basis of an example of the ...
    • The Effect of Temperature on the Gasification Process 

      Author: Baláš , Marek; Lisý , Martin; Štelcl , Ota
      (České vysoké učení technické v PrazeCzech Technical University in Prague, 2012)
      Gasification is a technology that uses fuel to produce power and heat. This technology is also suitable for biomass conversion. Biomass is a renewable energy source that is being developed to diversify the energy mix, so ...
    • Strontium As a Structure Modifier for Non-binary Al–Si Alloy 

      Author: Stunová , Barbora Bryksí
      (České vysoké učení technické v PrazeCzech Technical University in Prague, 2012)
      This paper presents a study of the influence on the structure of AlSi10Mg alloy when 400 ppm of strontium is added. Not only changes in the morphology of eutectic silicon, but in particular changes in the morphology of the ...
    • A Way to Use Waste Heat to Generate Thermoelectric Power 

      Author: Brázdil , Marian; Pospíšil , Jiří
      (České vysoké učení technické v PrazeCzech Technical University in Prague, 2012)
      In recent years there has been rising interest in thermoelectric generation as a potential source of electric power using waste heat. This paper describes thermoelectric power generation from waste heat from biomass boilers, ...
    • A Flexible Adjustment and Control System for Hydraulic Machines 

      Author: Banyai , Daniel; Marcu , Lucian
      (České vysoké učení technické v PrazeCzech Technical University in Prague, 2012)
      Due to the advantages of hydraulic systems with variable displacement, it was necessary to design a control system that can adjust the pressure, flow, power or a combination of these features, that can be easily integrated ...
    • Contributions to the Study of Dynamic Absorbers, a Case Study 

      Author: Balcau , Monica; Plesa , Angela; Opruta , Dan
      (České vysoké učení technické v PrazeCzech Technical University in Prague, 2012)
      Dynamic absorbers are used to reduce torsional vibrations. This paper studies the effect of a dynamic absorber attached to a mechanical system formed of three reduced masses which are acted on by one, two or three order x ...
    • Advanced Functions of a Modern Power Source for GMAW Welding of Steel 

      Author: Kolařík , Ladislav; Kolaříková , Marie; Kovanda , Karel; Pantůček , Marek; Vondrouš , Petr
      (České vysoké učení technické v PrazeCzech Technical University in Prague, 2012)
      This paper evaluates the use of a modern welding power source equipped with advanced arc control functions. At the Laboratory of Welding Technologies of CTU in Prague we have focused on GMAW welding of steel using Sigma ...
    • Creating a Multi-axis Machining Postprocessor 

      Author: Vavruška , Petr
      (České vysoké učení technické v PrazeCzech Technical University in Prague, 2012)
      This paper focuses on the postprocessor creation process. When using standard commercially available postprocessors it is often very difficult to modify its internal source code, and it is a very complex process, in many ...
    • Influence of the Amount of Master Alloy on the Properties of Austenitic Stainless Steel AISI 316L Powder Sintered in Hydrogen 

      Author: Skaloń , Mateusz; Kazior , Jan
      (České vysoké učení technické v PrazeCzech Technical University in Prague, 2012)
      AISI 316L austenitic stainless steel powder was modified with four different amounts of boron (0.1; 0.2; 0.3; 0.4 of wt. %) in the form of MasterAlloy micro-powder, and was sintered in a pure dry hydrogen atmosphere in ...
    • Concepts of Emission Reduction in Fluidized Bed Combustion of Biomass 

      Author: Purgar , Amon; Winter , Franz
      (České vysoké učení technické v PrazeCzech Technical University in Prague, 2012)
      A status report on fluidized bed technology in Austria is under preparation, in response to the Fluidized Bed Conversion multi-lateral technology initiative of the International Energy Agency. This status report focuses ...
    • Metallurgical Joining of Magnesium Alloys by the FSW Process 

      Author: Kupec , Tomáš; Hlavačová , Ivana; Turňa , Milan
      (České vysoké učení technické v PrazeCzech Technical University in Prague, 2012)
      This paper deals with welding AZ 31Mg alloy by FSW (Friction Stir Welding) technology. Welds were fabricated with new equipment supplied from China for VUZ-PI Bratislava (Welding Research Institute — Industrial Institute). ...