Řízení a vizualizace pro aplikaci speciálního pneumatického pohonu.
Control and vizualization of the special pneumatic drive application.
Typ dokumentu
diplomová prácemaster thesis
Autor
Natarajan Arun
Vedoucí práce
Martinásková Marie
Oponent práce
Škeřík Filip
Studijní obor
Přístrojová a řídicí technikaStudijní program
Strojní inženýrstvíInstituce přidělující hodnost
ústav přístrojové a řídící technikyPráva
A university thesis is a work protected by the Copyright Act. Extracts, copies and transcripts of the thesis are allowed for personal use only and at one?s own expense. The use of thesis should be in compliance with the Copyright Act http://www.mkcr.cz/assets/autorske-pravo/01-3982006.pdf and the citation ethics http://knihovny.cvut.cz/vychova/vskp.htmlVysokoškolská závěrečná práce je dílo chráněné autorským zákonem. Je možné pořizovat z něj na své náklady a pro svoji osobní potřebu výpisy, opisy a rozmnoženiny. Jeho využití musí být v souladu s autorským zákonem http://www.mkcr.cz/assets/autorske-pravo/01-3982006.pdf a citační etikou http://knihovny.cvut.cz/vychova/vskp.html
Metadata
Zobrazit celý záznamAbstrakt
This master thesis work mainly involves of the tact time measurements of the pneumatic actuator, with various types of load. The manual data are measured from the experiments done with using FESTO TP220 set. Aimed to gain knowledge about various types of actuators and compared those with TP220 supplements and know the actuators involved in the industries for transportation applications. Targeted to design a control by using PLC SIMATIC S7-200 also virtual control with GRAPHCET language. To prepare visualization of the semi-rotary drive using Reliance 4 Design SCADA software. The SCADA software design is used to monitor the process and to calculate the time of the semi-rotary drive. The entire process involves the communication between field level, PLC control and SCADA system. The communication is achieved from low level to high levels of automation. This master thesis work mainly involves of the tact time measurements of the pneumatic actuator, with various types of load. The manual data are measured from the experiments done with using FESTO TP220 set. Aimed to gain knowledge about various types of actuators and compared those with TP220 supplements and know the actuators involved in the industries for transportation applications. Targeted to design a control by using PLC SIMATIC S7-200 also virtual control with GRAPHCET language. To prepare visualization of the semi-rotary drive using Reliance 4 Design SCADA software. The SCADA software design is used to monitor the process and to calculate the time of the semi-rotary drive. The entire process involves the communication between field level, PLC control and SCADA system. The communication is achieved from low level to high levels of automation.
Kolekce
- Diplomové práce - 12110 [158]
Související záznamy
Zobrazují se záznamy příbuzné na základě názvu, autora a předmětu.
-
Funkčnost brýlových čoček pro řidiče
Autor: Bára Ježková; Vedoucí práce: Písařík Petr; Oponent práce: Bartoš Martin
(České vysoké učení technické v Praze. Vypočetní a informační centrum.Czech Technical University in Prague. Computing and Information Centre., 2023-06-19)V dnešní době se často řeší téma brýlových čoček pro řidiče. Jaké mají řidiči problémy při řízení, jako je např. oslnění, odlesky, a jak těmto problémům předejít. I na takové otázky tato bakalářská práce odpovídá. Především ... -
Mechanický upínací přípravek pro testování fan-drive motorů
Autor: Hradecký Jakub Milan; Vedoucí práce: Dynybyl Vojtěch; Oponent práce: Homolka Jakub
(České vysoké učení technické v Praze. Vypočetní a informační centrum.Czech Technical University in Prague. Computing and Information Centre., 2017-06-23)Tato bakalářská práce se zabývá návrhem upínací konstrukce pro fan-drive, na které jsou připojeny fan-drive motory, které zde budou testovány. Konstrukce je navržena tak, aby byla schopna držet i největší fan-drive, s ... -
Řízení a vizualizace pro aplikaci speciálních pneumatických pohonů s využitím ventilových terminálů
Autor: Burak Susam; Vedoucí práce: Martinásková Marie; Oponent práce: Škeřík Filip
(České vysoké učení technické v Praze. Vypočetní a informační centrum.Czech Technical University in Prague. Computing and Information Centre., 2019-06-22)ANNOTATION Title: Control and Visualization of the Pneumatic Drives Application Using Valve Terminals. Aim: Designing a sequence, simulating it, building a part of it and debugging it in the real world, visualizing a part ...