Influence of tempering on 3D printed samples from polymer material
Vliv temperace na 3D tištěné vzorky z polymerního materiálu
Authors
Supervisors
Reviewers
Editors
Other contributors
Journal Title
Journal ISSN
Volume Title
Publisher
České vysoké učení technické v Praze
Czech Technical University in Prague
Czech Technical University in Prague
Date of defense
Abstract
Diplomová práce na téma vliv temperace na 3D tištěné vzorky z polymerního materiálu představuje informace o aditivních technologiích používaných pro 3D tisk polymerních materiálů. Zvláště pak technologií fused deposition modeling (FDM) a materiálu glykolem modyfikovaný poethylentereftalát (PETG) a kompozitem PETG s uhlíkovým vláknem a možností tepelného zpracování výtisku z nich vyrobených. Dále se práce zabývá výrobou zkušebních tělísek z PETG a PETG s uhlíkovým vláknem a jejich žíháním při různých teplotách. Následně jsou provedeny zkoušky mechanických vlastností. Závěr práce tvoří porovnání mechanických vlastností obou materiálů a dosažených změn po žíhání.
The thesis on the effect of tempering on 3D printed polymer material samples presents information on additive technologies used for 3D printing of polymer materials. In particular, fused deposition modelling (FDM) technology and the material glycol modified polyethylene terephthalate (PETG) and PETG-carbon fibre composite and the possibility of heat treating prints made from them. Furthermore, the work deals with the fabrication of PETG and PETG with carbon fibre test bodies and their annealing at different temperatures. Subsequently, mechanical properties tests are performed. The thesis concludes with a comparison of the mechanical properties of the two materials and the changes obtained after annealing.
The thesis on the effect of tempering on 3D printed polymer material samples presents information on additive technologies used for 3D printing of polymer materials. In particular, fused deposition modelling (FDM) technology and the material glycol modified polyethylene terephthalate (PETG) and PETG-carbon fibre composite and the possibility of heat treating prints made from them. Furthermore, the work deals with the fabrication of PETG and PETG with carbon fibre test bodies and their annealing at different temperatures. Subsequently, mechanical properties tests are performed. The thesis concludes with a comparison of the mechanical properties of the two materials and the changes obtained after annealing.
Description
Keywords
3D tisk, aditivní technologie, Fused deposition modeling, FDM, polymerní materiály, filament, glykolem modyfikovaný polyethylentereftalát, PETG, PET-G, kompozitní materiály s polymerní matricí, vláknová výztuž, uhlíkové vlákno, žíhání, 3D print, additive technology, Fused deposition modeling, FDM, polymer materials, filament, polyethylene terephthalate glycol, PETG, PET-G, composite materials with polymers matrix, fiber reinforcement, carbon fiber, annealing
Citation
Underlying research data set URL
Permanent link
Rights/License
A university thesis is a work protected by the Copyright Act of the Czech Republic. Extracts, copies and transcripts of the thesis are allowed for personal use only and at one`s own expense. The use of thesis should be in compliance with the Copyright Act.
Vysokoškolská závěrečná práce je dílo chráněné autorským zákonem. Je možné pořizovat z něj na své náklady a pro svoji osobní potřebu výpisy, opisy a rozmnoženiny. Jeho využití musí být v souladu s autorským zákonem v platném znění.
Vysokoškolská závěrečná práce je dílo chráněné autorským zákonem. Je možné pořizovat z něj na své náklady a pro svoji osobní potřebu výpisy, opisy a rozmnoženiny. Jeho využití musí být v souladu s autorským zákonem v platném znění.