Návrh systému pro kontrolu těsnosti dýchacích soustav během lavinových experimentů
Technical design of leak detection in breathing circuits in simulated avalanche experiments
Typ dokumentu
bakalářská prácebachelor thesis
Autor
Jindřich Hrdina
Vedoucí práce
Horáková Lenka
Oponent práce
Kotenová Iva
Studijní obor
Biomedicínský technikStudijní program
Biomedicínská a klinická technikaInstituce přidělující hodnost
katedra biomedicínské technikyPráva
A university thesis is a work protected by the Copyright Act. Extracts, copies and transcripts of the thesis are allowed for personal use only and at one?s own expense. The use of thesis should be in compliance with the Copyright Act http://www.mkcr.cz/assets/autorske-pravo/01-3982006.pdf and the citation ethics http://knihovny.cvut.cz/vychova/vskp.htmlVysokoškolská závěrečná práce je dílo chráněné autorským zákonem. Je možné pořizovat z něj na své náklady a pro svoji osobní potřebu výpisy, opisy a rozmnoženiny. Jeho využití musí být v souladu s autorským zákonem http://www.mkcr.cz/assets/autorske-pravo/01-3982006.pdf a citační etikou http://knihovny.cvut.cz/vychova/vskp.html
Metadata
Zobrazit celý záznamAbstrakt
Návrh systému pro kontrolu těsnosti dýchacích soustav během lavinových experimentů Při experimentech simulujících dýchání pod lavinou se může vyskytnout problém s netěsností speciálně navržených dýchacích soustav. Cílem bakalářské práce bylo navrhnout a zrealizovat dvě technická řešení dávkování oxidu dusného jako sledovacího plynu, která budou schopná ověřit těsnost nejen v okolí dýchacích cest dobrovolníka, ale také v celé respirační soustavě. Díly, které nebyly běžně dostupné, byly vymodelovány speciálně pro tento systém. Bylo navrženo 9 komponentů v simulačním počítačovém programu COMSOL Multiphysics, jenž byly posléze vytisknuty na 3D tiskárně. Obě aparatury byly zkompletovány a ověřeny v klinické studii. Výsledky studie naznačují, že vhodnějším technickým řešením v okolí dýchacích cest probanda je to, které zahrnuje polomasku a to jak ve vnitřních, tak i vnějších podmínkách. Systém pro kontrolu netěsností u zbývajících komponentů byl ověřen pouze při pilotním měření v laboratorních podmínkách, ale aplikace při experimentech je komplikovaná, protože ztěžuje manipulaci s aparaturou. Technical design of leak detection in breathing circuits in simulated avalanche experiments During simulated avalanche breathing experiments, a problem of leakage in the specially designed respiratory systems may occur. The aim of this project is to design and implement two technical solutions for dosing nitrous oxide use as a tracing gas both in the surrounding of the patients' airways and in the entire breathing system. Parts that were not readily available had to be specifically developed for this system. In total, 9 components were designed in the COMSOL Multiphysics program and then printed on a 3D printer. Both designed systems were completed and tested in a clinical study. The results suggest that a system with half-face mask is a better technical solution for the detection around the subject's airways in both inner and outer conditions. The leakage detection system for the other components was tested only during a pilot study under laboratory conditions, however, the manipulation with this system makes this system cumbersome for these experiments
Kolekce
- Bakalářské práce - 17110 [869]