Investigation of the particle movement in rotary kiln
Investigation of the particle movement in rotary kiln
Typ dokumentu
diplomová prácemaster thesis
Autor
Ronzon Tirado José Renato
Vedoucí práce
Skočilas Jan
Oponent práce
Petera Karel
Studijní obor
Procesní technikaStudijní program
Strojní inženýrstvíInstituce přidělující hodnost
ústav procesní a zpracovatelské technikyObhájeno
2018-09-05Práva
A university thesis is a work protected by the Copyright Act. Extracts, copies and transcripts of the thesis are allowed for personal use only and at one?s own expense. The use of thesis should be in compliance with the Copyright Act http://www.mkcr.cz/assets/autorske-pravo/01-3982006.pdf and the citation ethics http://knihovny.cvut.cz/vychova/vskp.htmlVysokoškolská závěrečná práce je dílo chráněné autorským zákonem. Je možné pořizovat z něj na své náklady a pro svoji osobní potřebu výpisy, opisy a rozmnoženiny. Jeho využití musí být v souladu s autorským zákonem http://www.mkcr.cz/assets/autorske-pravo/01-3982006.pdf a citační etikou http://knihovny.cvut.cz/vychova/vskp.html
Metadata
Zobrazit celý záznamAbstrakt
This work is study of what a rotary kiln is and its applications for creating expanded ceramics, for which, a brief discussion of what is a rotary kiln, what is clay and ceramics, heat transfer inside the kiln, the movement of the particles inside the kiln and simulation methods on ANSYS are exposed. Four simulations were performed, two using a smooth kiln but with different simulation techniques, and two using inserts inside the kiln to disrupt the flow of material along the kiln. A comparison in between the expected values for residence time between published formulas and the simulations was done as well as an analysis between the particle size and the residence time. For this work, ANSYS 16.2, Inventor 2015, EasyFit, and Microsoft Office software were used, and a brief guide of the process followed by the software setting, running and data analysis is presented for each of the simulations. This work is study of what a rotary kiln is and its applications for creating expanded ceramics, for which, a brief discussion of what is a rotary kiln, what is clay and ceramics, heat transfer inside the kiln, the movement of the particles inside the kiln and simulation methods on ANSYS are exposed. Four simulations were performed, two using a smooth kiln but with different simulation techniques, and two using inserts inside the kiln to disrupt the flow of material along the kiln. A comparison in between the expected values for residence time between published formulas and the simulations was done as well as an analysis between the particle size and the residence time. For this work, ANSYS 16.2, Inventor 2015, EasyFit, and Microsoft Office software were used, and a brief guide of the process followed by the software setting, running and data analysis is presented for each of the simulations.
Kolekce
- Diplomové práce - 12118 [150]
Související záznamy
Zobrazují se záznamy příbuzné na základě názvu, autora a předmětu.
-
Řízení a vizualizace pro aplikaci speciálního pneumatického pohonu.
Autor: Natarajan Arun; Vedoucí práce: Martinásková Marie; Oponent práce: Škeřík Filip
(České vysoké učení technické v Praze. Vypočetní a informační centrum.Czech Technical University in Prague. Computing and Information Centre., 2017-06-19)This master thesis work mainly involves of the tact time measurements of the pneumatic actuator, with various types of load. The manual data are measured from the experiments done with using FESTO TP220 set. Aimed to gain ... -
Konstrukce otočné osy B brusky Studer S40
Autor: Štecher Jiří; Vedoucí práce: Červenka Jaroslav; Oponent práce: Kočiško Josef
(České vysoké učení technické v Praze. Vypočetní a informační centrum.Czech Technical University in Prague. Computing and Information Centre., 2017-07-12)Bakalářská práce se zabývá návrhem konstrukce otočné osy B brousicího vřeteníku brusky Studer S40. Návrh bere v úvahu požadavek firmy na použití stávajícího stolu s vřeteníkem a požadovanou přesnost polohování 0,001°. ... -
Otočný stůl pro pětiosé multifunkční centrum
Autor: Jakub Padevět; Vedoucí práce: Ondráček Miroslav; Oponent práce: Tíkal Josef
(České vysoké učení technické v Praze. Vypočetní a informační centrum.Czech Technical University in Prague. Computing and Information Centre., 2020-01-30)Tato práce se věnuje konstrukci otočného stolu pětiosého multifunkčního centra a návrhu jeho pohonu. Jsou zde popsány jednotlivé komponenty a typy konstrukcí otočného stolu. V další části je provedena volba komponent a ...