Optimalizace CPAP aplikátoru pro novorozence
Optimization of CPAP applicators for newborns
Type of document
diplomová prácemaster thesis
Author
Balcarová Eva
Supervisor
Kudrna Petr
Opponent
Hiřmanová Klára
Field of study
Biomedicínský inženýrStudy program
Biomedicínská a klinická technikaInstitutions assigning rank
katedra biomedicínské technikyDefended
2015-06-29Rights
A university thesis is a work protected by the Copyright Act. Extracts, copies and transcripts of the thesis are allowed for personal use only and at one?s own expense. The use of thesis should be in compliance with the Copyright Act http://www.mkcr.cz/assets/autorske-pravo/01-3982006.pdf and the citation ethics http://knihovny.cvut.cz/vychova/vskp.htmlVysokoškolská závěrečná práce je dílo chráněné autorským zákonem. Je možné pořizovat z něj na své náklady a pro svoji osobní potřebu výpisy, opisy a rozmnoženiny. Jeho využití musí být v souladu s autorským zákonem http://www.mkcr.cz/assets/autorske-pravo/01-3982006.pdf a citační etikou http://knihovny.cvut.cz/vychova/vskp.html
Metadata
Show full item recordAbstract
Ventilace pomocí pozitivního přetlaku nacházíuplatněnízejménavrespirační terapii neonatologických pacientů. Tato technika používá dva druhy aplikátorů ?nosní masky a aplikátory snostrilami. Každý zpoužívaných systémů má nežádoucí účinky, a to především deformace nosní přepážky. Cílem této práceje vytvořit model aplikátoru CPAP, který by odstranil tento problém. Předmětem experimentu byly dva aplikátory snostrilami, jeden znich kopíroval konstrukci stávajícího prvku a druhý byl modifikován tak, aby nedestruoval nosní přepážku. Tyto dva vytvořené prvky jsem později vytiskla pomocí 3D tiskárny a následně testovala. Metodika pro zhodnocení této práce spočívala votisknutí aplikátorů do tvárné hmoty a pro zhodnocení výsledků experimentu jsem použila grafické srovnání jednotlivých řezů a měřicí metodu s následným statistickým vyhodnocením pomocí t -testu. Nejproblematičtějším místem nosu novorozenců je nosní přepážka. Zde jsem dosáhla vkaždém změřených bodů vyšších středních hodnot tlouštěk řezu, a toaž o37,5 %oproti původnímu aplikátoru. Změnou konstrukčních vlastnostíbylo dosaženo snížení nadměrnéhotlakupůsobícíhona nosní přepážku neonatologického pacienta. Ventilation with positive pressure is used especially in the treatment of neonatal respiratory patients. This method uses two types of applicators -either nasal masks or prongs. Both of them have undesirable effects, especially deformation of the nasal septum. The aim of this work is to create a model of the applicator CPAP to eliminate that deformation. The subject of my study were two applicators with prongs. The first one represents the existing applicator and the other one is modified to protect nasal septum. I have printed these models using a 3D printer and then tested. The methodology for evaluation of this work was to make a negative of applicators into soft substance. To get the results of the experiment I used a graphical comparison of the single sections and measuring method with statistical evaluation by using t-test. The most problematic point of the infant nose is a nasal septum. In each of the measured points I have achieved higher meanvalue of thickness of section evenup to 37.5% compared to the original applicator. Improved design of applicatorcaused a reduction of excessive pressure to the nasal septum of infants
Collections
- Diplomové práce - 17110 [1011]