Now showing items 1-10 of 10

    • LABORATORY TESTING OF THE LEICA AT401 LASER TRACKER 

      Author: Dvořáček , Filip
      (České vysoké učení technické v PrazeCzech Technical University in Prague, 2016)
      This paper describes laboratory tests on a Leica AT401laser tracker. As the newer Leica AT402 model also uses the same firmware package, most of the results should also be valid for this device. First, we present the ...
    • A MATHEMATICAL MODEL OF GALVANIC CORROSION UNDER THE CONDITIONS OF A THIN ELECTROLYTE FILM 

      Author: Jeníček , Vít; Diblíková , Linda
      (České vysoké učení technické v PrazeCzech Technical University in Prague, 2016)
      A mathematical model of galvanic corrosion under the conditions of a thin electrolyte film was used to evaluate atmospheric corrosion. Experimentally determined weight loss values were used to validate the modelled results. ...
    • MEASUREMENTS ON THE VT 400 AIR TURBINE 

      Author: Klimko , Marek; Okresa , Daniel
      (České vysoké učení technické v PrazeCzech Technical University in Prague, 2016)
      This paper presents a basic description of measurements on the experimental air turbine located in the laboratories of the Department of Power System Engineering (KKE). The research on this turbine focuses on the flow in ...
    • INTEGRAL METHODS FOR DESCRIBING PULSATILE FLOW 

      Author: Hromadka , David; Chlup , Hynek; Žitný , Rudolf
      (České vysoké učení technické v PrazeCzech Technical University in Prague, 2016)
      This paper presents an approximate solution of the pulsatile flow of a Newtonian fluid in the laminar flow regime in a rigid tube of constant diameter. The model is represented by two ordinary differential equations. The ...
    • EXPERIMENTAL LEVELLING AT THE INTERFACE OF OPTICAL ENVIRONMENTS 

      Author: Sirůčková , Hana
      (České vysoké učení technické v PrazeCzech Technical University in Prague, 2016)
      The article discusses the problems of refraction and its impact on levelling at the interface of optical environments. It describes the influence of a vertical refraction and shows the results of investigating the effect ...
    • APPLICATION OF DIMENSIONAL ANALYSIS IN HEAT LOSS DETERMINING IN DISTRICT HEATING SYSTEMS 

      Author: Čarnogurská , Mária; Dobáková , Romana; Příhoda , Miroslav
      (České vysoké učení technické v PrazeCzech Technical University in Prague, 2016)
      Existing procedures for determining the heat loss in heat distribution use balance relations, or rather they are based on the theory of heat and mass transfer. Dimensional analysis enables a new point of view that demonstrated ...
    • ULTRASONIC SOLDERING OF Cu AND Al2O3 CERAMICS BY USE OF Bi-La AND Bi-Ag-La SOLDERS 

      Author: Koleňák , Roman; Prach , Michal; Kostolný , Igor
      (České vysoké učení technické v PrazeCzech Technical University in Prague, 2016)
      This work deals with the effect of solder alloying with a small amount of lanthanum on joint formation with metallic and ceramic substrate. The Bi-Ag – based solder with 2 wt.% lanthanum addition and Bi solder with 2 wt.% ...
    • TESTS ON 10.9 BOLTS UNDER COMBINED TENSION AND SHEAR 

      Author: Kawohl Katherine, Anne; Lange , Jörg
      (České vysoké učení technické v PrazeCzech Technical University in Prague, 2016)
      Prior investigations of the load-bearing capacity of bolts during fire have shown differing behaviour between bolts that have been loaded by shear or by tensile loads. A combination of the two loads has not yet been examined ...
    • ELASTO-KINEMATIC COMPUTATIONAL MODEL OF SUSPENSION WITH FLEXIBLE SUPPORTING ELEMENTS 

      Author: Vrána , Tomáš; Bradáč , Josef; Kovanda , Jan
      (České vysoké učení technické v PrazeCzech Technical University in Prague, 2016)
      This paper analyzes the impact of flexibility of individual supporting elements of independent suspension on its elasto-kinematic characteristics. The toe and camber angle are the geometric parameters of the suspension, ...
    • PARAMETRIC STUDIES ON THE COMPONENT-BASED APPROACH TO MODELLING BEAM BOTTOM FLANGE BUCKLING AT ELEVATED TEMPERATURES 

      Author: Quan , Guan; Huang , Shan-Shan; Burgess , Ian
      (České vysoké učení technické v PrazeCzech Technical University in Prague, 2016)
      In this study, an analytical model of the combination of beam-web shear buckling and bottom-flange buckling at elevated temperatures has been introduced. This analytical model is able to track the force-deflection path ...