Aplikace technologie LSP na 3D tištěný povrch materiálu AlSi10Mg
Laser shock peening technique application on 3D printed surface of AlSi10Mg Alloy
dc.contributor.advisor | Beránek Libor | |
dc.contributor.author | Zbyněk Soukup | |
dc.date.accessioned | 2022-08-26T22:51:57Z | |
dc.date.available | 2022-08-26T22:51:57Z | |
dc.date.issued | 2022-08-26 | |
dc.identifier | KOS-1083279949705 | |
dc.identifier.uri | http://hdl.handle.net/10467/103478 | |
dc.description.abstract | Práce je zaměřená na použití technologie Laser shock peening na 3D tištěný povrch materiálu AlSi10Mg. Teoretická část se věnuje integritě povrchu, dokončovacím metodám a LSP technologii. V praktické části byly vyhodnoceny vybrané parametry integrity povrchu 3D tištěných vzorků. Parametry byly porovnány před použitím a po použití technologie LSP. Cílem práce bylo zhodnocení vybraných parametrů a celkové možnosti využití technologie LSP na 3D tištěný materiál. | cze |
dc.description.abstract | The work is focusing on application of LSP technique on 3D printed surface of AlSi10Mg alloy. Theoretical part describes surface integrity, finishing methods and LSP technique. The practical part evaluates chosen parameters of surface integrity 3D printed parts. The parameters were compared before application of LSP and after. The aim of this bachelor 's work was evaluation of the parameters and utilization LSP on 3D printed surface. | eng |
dc.publisher | České vysoké učení technické v Praze. Vypočetní a informační centrum. | cze |
dc.publisher | Czech Technical University in Prague. Computing and Information Centre. | eng |
dc.rights | A university thesis is a work protected by the Copyright Act. Extracts, copies and transcripts of the thesis are allowed for personal use only and at one?s own expense. The use of thesis should be in compliance with the Copyright Act http://www.mkcr.cz/assets/autorske-pravo/01-3982006.pdf and the citation ethics http://knihovny.cvut.cz/vychova/vskp.html | eng |
dc.rights | Vysokoškolská závěrečná práce je dílo chráněné autorským zákonem. Je možné pořizovat z něj na své náklady a pro svoji osobní potřebu výpisy, opisy a rozmnoženiny. Jeho využití musí být v souladu s autorským zákonem http://www.mkcr.cz/assets/autorske-pravo/01-3982006.pdf a citační etikou http://knihovny.cvut.cz/vychova/vskp.html | cze |
dc.subject | integrita povrchu | cze |
dc.subject | textura povrchu | cze |
dc.subject | dokončovací metody | cze |
dc.subject | laser | cze |
dc.subject | laser shock peening | cze |
dc.subject | 3D tisk | cze |
dc.subject | výpočetní tomografie | cze |
dc.subject | porozita | cze |
dc.subject | surface integrity | eng |
dc.subject | surface texture | eng |
dc.subject | finishing methods | eng |
dc.subject | laser | eng |
dc.subject | laser shock peening | eng |
dc.subject | 3D printing | eng |
dc.subject | computed tomography | eng |
dc.subject | porosity | eng |
dc.title | Aplikace technologie LSP na 3D tištěný povrch materiálu AlSi10Mg | cze |
dc.title | Laser shock peening technique application on 3D printed surface of AlSi10Mg Alloy | eng |
dc.type | bakalářská práce | cze |
dc.type | bachelor thesis | eng |
dc.contributor.referee | Brajer Jan | |
theses.degree.discipline | Technologie, materiály a ekonomika strojírenství | cze |
theses.degree.grantor | ústav technologie obrábění, projektování a metrologie | cze |
theses.degree.programme | Výroba a ekonomika ve strojírenství | cze |
Soubory tohoto záznamu
Tento záznam se objevuje v následujících kolekcích
-
Bakalářské práce - 12134 [366]