Drcení odpadů
Mechanical size reduction of wastes
Typ dokumentu
diplomová prácemaster thesis
Autor
Chvátal Jan
Vedoucí práce
Krátký Lukáš
Oponent práce
Jirout Tomáš
Studijní obor
Procesní technikaStudijní program
Strojní inženýrstvíInstituce přidělující hodnost
ústav procesní a zpracovatelské technikyObhájeno
2018-09-04Práva
A university thesis is a work protected by the Copyright Act. Extracts, copies and transcripts of the thesis are allowed for personal use only and at one?s own expense. The use of thesis should be in compliance with the Copyright Act http://www.mkcr.cz/assets/autorske-pravo/01-3982006.pdf and the citation ethics http://knihovny.cvut.cz/vychova/vskp.htmlVysokoškolská závěrečná práce je dílo chráněné autorským zákonem. Je možné pořizovat z něj na své náklady a pro svoji osobní potřebu výpisy, opisy a rozmnoženiny. Jeho využití musí být v souladu s autorským zákonem http://www.mkcr.cz/assets/autorske-pravo/01-3982006.pdf a citační etikou http://knihovny.cvut.cz/vychova/vskp.html
Metadata
Zobrazit celý záznamAbstrakt
Tato práce se zabývá problematikou drcení odpadů, hlavně pak pneumatik. Práce je koncipována chronologicky, tedy od primárního drcení celých pneumatik až po mletí na jemný prášek s velikostí částic v řádu desetin milimetru. V následující části je popsána technologie mletí tak, jak ji aplikuje firma Lavaris. Nejprve je linka popsána obecně, načež práce přechází v detailní popis jednotlivých zařízení. Po zadefinování parametrů vstupního gumového granulátu přichází již na řadu experimentální část. Ta zkoumá vliv tří variant mlecích segmentů na výslednou jemnost částic. Pro každý typ segmentů je provedeno dvanáct měření, která se od sebe liší kromě rozdílného nastavení vzdálenosti mezi rotory i čtyřmi různými stupni otáček. Na experimentální část navazuje posouzení naměřených dat. V práci je hlavní důraz kladen na hodnocení přeměny výkonu mlýna na teplo a rozpojovací energii. Právě z této energie je následně stanovena Bondova konstanta, která vyjadřuje závislost mezi rozpojovací energií, velikostí částic na vstupu do mlýna a velikostí částic rozemletých. Ve svém závěru tato práce odhaluje možné nedostatky této technologie a nastiňuje možnosti k optimalizaci linky. This thesis deals with the problem of shredding waste, especially the tires. The work is conceived chronologically, from primary crushing of whole tires to milling to fine powder with particle size in the order of tenths of a millimeter. The following section describes the milling technology as applied by the Lavaris company. First the line is described in general, whereupon the work is passed in a detailed description of each device. After defining the parameters of the input rubber granulate it comes to the experimental part. It examines the influence of three variants of grinding segments on the resulting fineness of particles. For each type of segment, twelve measurements are made, which differ from each other in addition to the different adjustment of the distance between the rotors and four different stages of rotation. The experimental part follows the assessment of measured data. At thesis, the main emphasis is placed on the evaluation of the conversion performance of the mill to heat and decoupling energy. This energy is then determined by a Bond´s constant, which expresses the dependence between decoupling energy, particle size on the mill inlet and the size of the milled particle. In its conclusion, this thesis reveals possible shortcomings of this technology and outlines the possibilities to optimize the line.
Kolekce
- Diplomové práce - 12118 [150]